David Babakaiff
Written by David Babakaiff · Co-Founder, VanPlex | 25+ Years BC Construction Last reviewed: October 2026

San Jose | Zoning Districts

San Jose Zoning Districts: R-1, R-2, R-M and How Many Homes Each Allows

A zoning district is the label the City puts on each lot to say what may be built there. San Jose writes its districts in Title 20 of the Municipal Code. This page reads the residential districts, the table of uses each one allows, and the routes that let a lot hold more homes than its district name suggests. Every rule here comes from the code as published in Supplement 5 Update 3, which carries City ordinances through June 16, 2026. The San Jose overview gives the short version.

San Jose zoning in six facts

The Residential Districts

Section 20.10.060 sets up the City's zoning districts in Table 20-10. The table lists them "in descending order of restrictiveness, that is, with the most restrictive district listed first and the least restrictive district listed last." Open space and agriculture come first, then the residential districts, then commercial, mixed use and industrial ones. Eight districts are residential.

District Name in Table 20-10 Older map symbols Minimum lot area
R-1-RR Rural Residential (1 home per 5 acres) None 5 acres
R-1-1 Residence District (1 home per acre) R-1-B-3 43,560 sq ft
R-1-2 Residence District (2 homes per acre) R-1-B-2 20,000 sq ft
R-1-5 Residence District (5 homes per acre) R-1-B-8, R-1-B-1 8,000 sq ft
R-1-8 Residence District (8 homes per acre) R-1, R-1-B-6 5,445 sq ft
R-2 Residence District (2 homes per lot) R-2 5,445 sq ft
R-M Residence District (multiple units per lot) R-3, R-3-F, R-3-A, R-3-B, R-3-C, R-4 6,000 sq ft
R-MH Mobilehome parks and travel trailer parks T-M 6,000 sq ft

Sources: San Jose Municipal Code Table 20-10 (Section 20.10.060) and Table 20-60 (Section 20.30.200), Supplement 5 Update 3.

The column of older map symbols matters on older parcels. Table 20-10 gives each district an alternative symbol, so a lot still shown as R-1 or R-1-B-6 on an old map is read as R-1-8, and a lot shown as R-3 or R-4 is read as R-M. The number after R-1 is the planned density in homes per acre: R-1-1 is one home per acre and R-1-8 is eight. R-1-RR, the rural residential district, is one home per five acres.

Section 20.30.010 gives the purpose of each district. R-1 is "to reserve land for the construction, use and occupancy of single-family subdivisions." For R-1, "The allowable density range for the R-1 districts is one to eight dwelling units per acre." R-2 reserves land for "single-family and two-family subdivisions," and "The allowable density range for the R-2 district is eight to sixteen dwelling units per acre." R-M is for "higher density residential development and higher density residential-commercial mixed use development." The code gives R-M no density range of its own. R-MH is for mobilehome parks.

What Each District Allows

Table 20-50 in Section 20.30.100 is the list of uses. A "P" means the use is permitted with no special permit, a "C" needs a conditional use permit decided at a hearing, and a dash means the use is not allowed. The code adds: "Land uses not listed on Table 20-50 are not permitted." The rows that matter for homes are these.

Use R-1 R-2 R-M R-MH
One-family dwelling (a house) Permitted Permitted Permitted Conditional use permit
Accessory dwelling unit (ADU) Permitted Permitted Permitted Not allowed
Two-family dwelling (a duplex) Not allowed Permitted Permitted Not allowed
Multiple dwelling (three or more homes) Not allowed Not allowed Permitted Not allowed
Guesthouse Not allowed Not allowed Conditional use permit Not allowed

Source: San Jose Municipal Code Section 20.30.100, Table 20-50, last amended by Ordinances 31298 and 31329.

Two notes under the table set the home count. Note 1 says: "Only one one-family dwelling unit per lot in the R-1, R-2, R-M and R-MH districts, unless allowed pursuant to the provisions of Part 8, Part 9, or Part 9.5." Part 8 is the City's SB 9 rules, Part 9 is the 2026 two-unit rule for R-2 lots, and Part 9.5 covers properties on the Historic Resources Inventory. Note 2 says: "A maximum of two primary living units per lot, with Accessory Dwelling Units, are permitted in the R-2 district." A primary living unit is a main home, as opposed to an accessory dwelling unit (ADU), which is a smaller second home on the same lot.

Note 10 lets every listed home type be used as transitional housing, and says supportive and transitional housing "shall be subject only to those restrictions that apply to other residential dwellings of the same type within the same zone." Permanent supportive housing is permitted in all four districts.

How Many Homes Fit on One Lot

The district name is a starting point. Several parts of the code add homes on top of it, and each has its own rules. This table gathers them in one place, with the section that sets each number.

Route Code Homes allowed
R-1 lot, state ADU rules in the city code SJMC 20.80.175(B)(1) House plus 1 attached or detached ADU and 1 junior ADU
R-1 lot under SB 9, no split SJMC 20.30.820(A) 2 main homes; 4 units at most with ADUs
R-1 lot under SB 9, split into two SJMC 20.30.810(E) 2 units on each new lot
R-2 lot under Part 9 SJMC 20.30.852(A) 2 houses or a duplex; 5 units at most with ADUs
R-M lot SJMC Table 20-50 Multiple dwelling permitted; no unit count in Table 20-60
Small-lot subdivision (SB 684 or SB 1123) SJMC 20.195.450(A) Up to 10 units on up to 10 lots

Sources: San Jose Municipal Code 20.80.175, 20.30.810 and 20.30.820, 20.30.852 and 20.195.450.

  • R-1 with ADUs. Section 20.80.175 allows, on a lot with a house, "one (1) attached or one (1) detached Accessory Dwelling Unit, and one (1) Junior Accessory Dwelling Unit." A junior ADU is a unit of 500 square feet or less inside the house. Section 20.80.176 opens the state's streamlined ADU list as a separate path. The ADUs and SB 9 page explains both.
  • R-1 with SB 9. Part 8 allows "two (2) one-family dwellings or one (1) two-family dwelling" per lot and caps the total at four units on an undivided lot.
  • R-2 with Part 9. Ordinance 31298, adopted February 3, 2026, gave R-2 lots a similar two-home approval by staff, with ADUs added up to "a maximum of five (5) units on any undivided lot."
  • R-M. A multiple dwelling is permitted, and Table 20-60 sets no unit count for R-M. The number of homes comes from height, setbacks, the General Plan and the permit that applies.
  • Small-lot subdivisions. Section 20.195.450 carries out the state laws known as SB 684 and SB 1123, which allow up to 10 lots and 10 homes. See the lot size page.

SB 9 and Part 9 set their own unit counts for each lot. For SB 9, Section 20.30.800 adds that where Part 8 or SB 9 "conflict with any other provisions of this Code, this Part and Senate Bill 9 shall control." Section 20.30.230 also keeps older small lots usable: a lot on an approved final subdivision map that is smaller than its district minimum, "but not less than three thousand square feet," keeps the area shown on that map as its minimum.

Size Limits That Come With the District

Table 20-60 sets a maximum height of 35 feet in every R-1 district and in R-2, with 2.5 stories at most. R-M allows "45 or established in Chapter 20.85," and R-MH allows 45 feet and 3 stories. For floor area, the table points to Part 9 of Chapter 20.100, the single-family house permit. That part applies "only" to "single-family homes developed in the R-1, R-2 and RM zoning districts." A new house with a floor area ratio of 0.45 or less, 30 feet or less in height and two stories or less needs no house permit. Floor area ratio is the building's floor area divided by the lot area.

SB 9 and Part 9 homes follow their own limits: 30 feet or two stories, whichever is lower, and a floor area ratio of 0.65 for each lot. The parking, setbacks and height page sets out all of these side by side.

Planned Development Zoning

Some San Jose lots carry a Planned Development (PD) label on top of a base district. Section 20.10.070 says "Every PD district shall be combined with an alternative base zoning district or districts," and the zone is written as the base symbol followed by (PD), for example A(PD). The PD zone is adopted with a general development plan, and building must follow a PD permit that matches that plan.

The City keeps full control of that permit. The code says: "The discretion to grant or deny such permit is untrammeled." Untrammeled means without limits. It also says "Unless and until a PD permit has been issued and becomes effective, the subject territory may be used only as if it were situate in the base district alone." For an owner, that means a PD lot can always fall back to its base district rules. A single-family house in a PD zone also falls under the PD permit rules, through Section 20.100.1030(D)(2).

Urban Village and Mixed Use Districts

Chapter 20.55 sets six more districts where homes can go: UVC, UV, MUC, MUN, UR and TR. The code says they support the General Plan "by providing flexibility for the development of employment uses, high density housing, and mixed use development." Section 20.55.020 calls Urban Villages one of the General Plan's "Major Strategies" for growth, and an approved Urban Village Plan's standards "shall prevail over the standards in this Chapter."

  • UVC. "Residential uses are not permitted in the UVC district."
  • UV and MUC. Multiple dwellings, mixed use buildings and ADUs are permitted under Table 20-138; one-family and two-family dwellings are not.
  • MUN, UR and TR. One-family, two-family and multiple dwellings are all permitted under Table 20-138.
  • MUN density. Under the conventional standards of Table 20-137, each home needs "1,452 square feet per unit" of lot area, and homes are capped at 30 per acre.

The City's own streamlined infill rules, covered on the three or more homes page, apply only on land with an Urban Residential, Transit Residential, Urban Village or Mixed Use Commercial General Plan designation.

Housing Overlays

An overlay is a second map layer that adds rules to the base district. Chapter 20.65 sets three that are about housing. The Affordable Housing Overlay and the Mixed-Income Housing Overlay cover mapped sites in North San Jose; the first "requires the construction of 100% affordable units" and the second "requires the construction of 25% affordable units." The Housing Element Residential Overlay covers sites named in the Housing Element. There, a project "must allow a minimum density of 30 dwelling units per acre" and residential uses are allowed by right when "at least 20% of the units are affordable" to lower income households.

Finding Your Lot's District

Section 20.10.080 says all City land "has been divided into zoning districts shown on the official zoning maps maintained in the office of the director." Rezonings are adopted by separate ordinances, which the code says are "deemed incorporated into the official maps." Because they are not printed in the codified code, the map is the record to check. "Any property located in the city that has not been specifically designated with a particular zoning district is hereby deemed to be zoned A-Agriculture." Where a boundary line is unclear, Section 20.10.090 says it runs along "the center line of the street unless otherwise clearly delineated."

Before you plan more homes, confirm three things: the base district, any PD label, and any overlay. Then check whether the lot is in a flood zone, fire hazard zone or earthquake fault zone, because Part 9 does not apply on those lots.

Best For

  • ✓ R-2 lots outside flood, fire and fault zones, where Part 9 allows up to five units.
  • ✓ R-1 lots with an existing house, where SB 9 allows two main homes and four units in total.
  • ✓ R-M and MUN, UR or TR lots, where buildings of three or more homes are permitted uses.

Usually Fails When

  • ✕ The plan puts a duplex or apartment building on R-1 land outside SB 9 or a small-lot map.
  • ✕ The lot is zoned UVC, where homes are not permitted.
  • ✕ A PD permit is needed and the City declines it, which the code allows.

What To Verify Before Spending Money

  • → Your district, PD label and overlay on the official zoning map.
  • → Flood, fire hazard and earthquake fault maps before relying on Part 9.
  • → Whether the lot is on the Historic Resources Inventory, which moves it to Part 9.5.

Where to Go Next

Related on VanPlex: the San Jose overview, SB 9 in California and the duplex to fourplex guide.

Frequently Asked Questions

What zoning districts does San Jose use for homes? +
San Jose Municipal Code Table 20-10 lists eight residential districts: R-1-RR, R-1-1, R-1-2, R-1-5 and R-1-8 for single-family land, R-2 for two-family land, R-M for multiple dwellings and R-MH for mobilehome parks. The urban village and mixed use districts UV, MUC, MUN, UR and TR also allow homes, and a Planned Development zone sits on top of one of these base districts.
What does the number after R-1 mean in San Jose? +
The number gives the planned density. In San Jose Table 20-10, R-1-1 is one home per acre, R-1-2 is two, R-1-5 is five and R-1-8 is eight, and R-1-RR is one home per five acres. Each district also has its own minimum lot area in Table 20-60, from 5,445 square feet in R-1-8 to 5 acres in R-1-RR.
Can I build a duplex on an R-1 lot in San Jose? +
Yes, through SB 9 (2021) or a small-lot subdivision. San Jose Table 20-50 does not list a two-family dwelling as a permitted use in R-1, and Note 1 allows one house per lot unless Part 8, Part 9 or Part 9.5 of Chapter 20.30 applies. Part 8, the San Jose SB 9 rules, allows two houses or one duplex on an R-1 lot, with four units in total including ADUs.
How many homes can I build on an R-2 lot in San Jose? +
Up to five on an undivided lot. San Jose Municipal Code 20.30.852 allows two houses plus a detached ADU, a converted ADU and a junior ADU, or a duplex plus two detached ADUs and one attached ADU. Part 9 does not apply in flood zones, fire hazard zones, earthquake fault zones and the other areas listed in 20.30.850(C).
Which San Jose zone allows apartment buildings? +
Among the residential districts, only R-M permits a multiple dwelling under San Jose Table 20-50. The urban village and mixed use districts UV, MUC, MUN, UR and TR also permit multiple dwellings under Table 20-138, while UVC does not allow homes. Other routes exist on R-1 and R-2 land, such as the small-lot subdivision of up to 10 units.
What is the old R-3 or R-4 zone in San Jose now? +
San Jose Table 20-10 treats R-3, R-3-F, R-3-A, R-3-B, R-3-C and R-4 as alternative map symbols for the R-M Residence District. In the same way, R-1 and R-1-B-6 are read as R-1-8, R-1-B-3 as R-1-1, and T-M as R-MH. A lot still marked with an older symbol follows the rules of the district it maps to.
What is a Planned Development zone in San Jose? +
A Planned Development (PD) zone is a custom district combined with a base district, written as the base symbol followed by (PD), under San Jose Municipal Code 20.10.070. Building follows a PD permit that matches the adopted general development plan. The code says the discretion to grant or deny a PD permit is untrammeled. Until one is issued, the base district rules apply.
How do I find the zoning of my San Jose lot? +
Check the official zoning maps kept by the Director of Planning, Building and Code Enforcement, which San Jose Municipal Code 20.10.080 makes the record of every zone. Rezonings are adopted by separate ordinances and are not printed in the codified code. Land with no district shown is deemed zoned A, Agriculture.
What is the MUN zone in San Jose? +
MUN is the Mixed Use Neighborhood district. San Jose Table 20-138 permits one-family, two-family and multiple dwellings there. Under the conventional standards in Table 20-137, each home needs 1,452 square feet of lot area, and residential density may not exceed 30 homes per acre. A single-family house on a lot of 6,000 square feet or more has a 0.45 floor area ratio limit.
Does San Jose have overlay zones for housing? +
Yes. San Jose Chapter 20.65 sets three housing overlays. The Affordable Housing Overlay requires 100 percent affordable homes and the Mixed-Income Housing Overlay requires 25 percent, both on mapped sites in North San Jose. The Housing Element Residential Overlay allows homes by right at 30 or more per acre when at least 20 percent are affordable to lower income households.

Official sources (checked October 2026)

SJMC Chapter 20.10, general provisions and zoning districts, Table 20-10
https://library.municode.com/ca/san_jose/codes/code_of_ordinances?nodeId=TIT20ZO_CH20.10GEPRZODI
SJMC Chapter 20.30, Part 2, uses allowed, Table 20-50
https://library.municode.com/ca/san_jose/codes/code_of_ordinances?nodeId=TIT20ZO_CH20.30REZODI_PT2USAL
SJMC Chapter 20.30, Part 3, development standards, Table 20-60
https://library.municode.com/ca/san_jose/codes/code_of_ordinances?nodeId=TIT20ZO_CH20.30REZODI_PT3DERE
SJMC Chapter 20.30, Part 8, SB 9 implementation
https://library.municode.com/ca/san_jose/codes/code_of_ordinances?nodeId=TIT20ZO_CH20.30REZODI_PT8SEBI9IM
SJMC Chapter 20.30, Part 9, two-unit development in R-2
https://library.municode.com/ca/san_jose/codes/code_of_ordinances?nodeId=TIT20ZO_CH20.30REZODI_PT9CIPESTIMTITDESILOWITMIZODI
SJMC Chapter 20.55, urban village and mixed use districts
https://library.municode.com/ca/san_jose/codes/code_of_ordinances?nodeId=TIT20ZO_CH20.55URVIMIUSZODI
SJMC Chapter 20.65, overlay districts
https://library.municode.com/ca/san_jose/codes/code_of_ordinances?nodeId=TIT20ZO_CH20.65OVDI
SJMC Chapter 20.80, Part 2.75, accessory dwelling units
https://library.municode.com/ca/san_jose/codes/code_of_ordinances?nodeId=TIT20ZO_CH20.80SPUSRE_PT2.75ACDWUN
SJMC Chapter 20.100, Part 9, single-family house permit
https://library.municode.com/ca/san_jose/codes/code_of_ordinances?nodeId=TIT20ZO_CH20.100ADPE_PT9SIMIHOPE
SJMC Supplement History Table (Supplement 5 Update 3)
https://library.municode.com/ca/san_jose/codes/code_of_ordinances?nodeId=SUHITA
VanPlex newsletter

Get new guides by email

New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.

General information, not legal advice. California housing law changes every year, and each city adds its own rules on top of state law. Confirm current requirements with the city or county planning department, and with a California-licensed attorney or architect, before you buy land or file plans.

Planning a multiplex in San Jose?

VanPlex builds multiplexes in British Columbia, Canada. For a lot in San Jose, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.

Get a proforma for your address