David Babakaiff
Written by David Babakaiff · Co-Founder, VanPlex | 25+ Years BC Construction Last reviewed: October 2026

Dallas | Townhouses and Multifamily

Dallas Townhouses, Triplexes, Fourplexes and Apartments, and SB 840

Three or more homes on one Dallas site need the right zoning. The townhouse districts allow 6 to 12 houses per acre on small lots, the clustered housing district allows 18, and the four multifamily districts allow apartment buildings, counted by lot area or by a density cap of up to 160 homes per acre. Since 2025, state law (SB 840) also opens most commercial land to apartments. This page gives the numbers for each, with the lot a small building needs. The Dallas overview gives the short version.

Three or more homes in Dallas in six facts

Which Districts Allow Three or More Homes

The City's district summaries name a primary use for each district. The three townhouse districts list "Single Family and Duplex Residential," with houses on lots of 2,000 square feet that can share walls. The CH district lists "Single Family, Duplex, Residential and Multifamily." The four MF districts list "Multifamily," a building or site with several homes. The seven single-family districts and the D district list one home or a duplex per lot, so a triplex or fourplex there needs a rezoning, and ForwardDallas 2.0, the City's land use plan, says it "does not allow multiplexes on any single-family zoned property in Dallas."

Whether the City treats a triplex or fourplex as a "multifamily" use is a question to put to zoning staff early. State law has its own definition for SB 840: "multifamily residential" means "a site for three or more dwelling units within one or more buildings." The summaries below are staff guides to the code, and each says "There may be exceptions to this information."

District Density Lot area Height Lot coverage
TH-1(A) 6 per acre 2,000 sq ft per house 36 ft 60 percent (80 on one lot within a 60 percent project)
TH-2(A) 9 per acre 2,000 sq ft per house 36 ft Same
TH-3(A) 12 per acre 2,000 sq ft per house 36 ft Same
CH 18 per net acre 2,000 sq ft per home 36 ft 60 percent
MF-1(A) No cap 1,000 to 1,800 sq ft per apartment, plus 200 per bedroom over two 36 ft 60 percent
MF-1(SAH) 15 to 30 per net acre As MF-1(A) 36 ft 60 percent
MF-2(A) No cap 800 to 1,200 sq ft per apartment, plus 150 per bedroom over two 36 ft 60 percent
MF-2(SAH) 20 to 40 per net acre As MF-2(A) 36 ft 60 percent
MF-3(A) 90 per net acre 6,000 sq ft lot; 450 to 550 sq ft per apartment 90 ft 60 percent
MF-4(A) 160 per net acre 6,000 sq ft lot; 225 to 325 sq ft per apartment 240 ft 80 percent

Source: City of Dallas Current Planning summaries for TH-1(A), TH-2(A), TH-3(A), CH, MF-1, MF-2, MF-3(A) and MF-4(A), read October 9, 2026.

Townhouse Districts

Each townhouse district sets "2,000 square feet for single family structures; and 6,000 square feet for duplex structures," with no minimum front yard and a 36-foot height limit. The density cap sets the total: TH-1(A) allows "No more than 6 dwelling units for each acre," TH-2(A) 9 and TH-3(A) 12. On a one-acre site a TH-3(A) project can hold 12 houses, and the lots can be as small as 2,000 square feet as long as the total stays at 12.

The coverage rule lets single lots be dense when the project keeps open space: "80% of individual lot may be covered by structures if the coverage for the total project does not exceed 60% and at least 40% is reserved for open space." Side and rear yards have "No minimum for single family structures." A plat must leave "a minimum of 15 feet between group of eight single family structures."

Ordinance No. 30930, which rewrote the single-family use rules in 2018, sets rules for attached houses. "Except for the foundation, a dwelling unit must be physically separable from contiguous dwelling units in the event of removal of a dwelling unit." "Each party wall must be governed by a set of deed restrictions, stipulating that if a dwelling unit is removed, the party wall stays with the remaining dwelling unit." A party wall is the shared wall between two attached homes. And "Each dwelling unit must have separate utility services," though general services on land a homeowners association owns are allowed. Since May 14, 2025 a house in a townhouse district needs one parking space.

The Clustered Housing District

CH allows more homes per acre than the townhouse districts and fewer than MF-3(A) or MF-4(A). The CH summary sets "Maximum dwelling unit density is 18 dwelling units per net acre," a "Minimum lot size is 2000 square feet for each dwelling unit," a 36-foot height limit and 60 percent coverage. "No group of attached dwelling units may exceed eight in number." The front yard is 15 feet next to an expressway or thoroughfare and zero elsewhere; side and rear yards are 10 feet where the lot is next to or across an alley from a district other than TH(A), and zero elsewhere.

A CH district must cover "a minimum of one-half acre" unless the City Council "determines that a smaller district is justified in a transitional circumstance separating a residential district from a higher density district." So a CH rezoning suits a site of half an acre or more, or a site between houses and apartments.

Multifamily Districts: Lot Area per Home

MF-1(A) and MF-2(A) have "No maximum dwelling unit density." Instead each home needs a set amount of lot, by bedroom count. In MF-1(A) an apartment with "No separate bedroom" needs 1,000 square feet, one bedroom 1,400, two bedrooms 1,800, and 200 more for each bedroom over two. In MF-2(A) the figures are 800, 1,000 and 1,200, plus 150. Both allow 36 feet of height and 60 percent coverage, and need a 15-foot front yard and 10-foot side and 15-foot rear yards for a building other than a house or duplex. The rear yard may be 10 feet "when a building site backs on a district other than residential, except for MF(A) district."

Example building Lot area per home Lot needed
Fourplex of two-bedroom units, MF-2(A) 4 x 1,200 sq ft 4,800 sq ft
Fourplex of two-bedroom units, MF-1(A) 4 x 1,800 sq ft 7,200 sq ft
Triplex of one-bedroom units, MF-1(A) 3 x 1,400 sq ft 4,200 sq ft
Four homes, CH 4 x 2,000 sq ft 8,000 sq ft
Six two-bedroom units, MF-3(A) 6 x 550 sq ft, but the lot must be 6,000 sq ft 6,000 sq ft

VanPlex arithmetic on the per-home lot areas in the City's MF-1(A), MF-2(A), MF-3(A) and CH summaries. Yards, coverage and any planned development rules can require a larger lot.

SAH versions. MF-1 and MF-2 each have a version marked SAH, with a density cap tied to the share of "SAH Units Provided." In MF-1(SAH) the cap is 15 homes per net acre with none, then 16, 17 and 20, and 30 with 20 percent. In MF-2(SAH) it runs 20, 22, 24, 30 and 40. The summary does not define SAH; ask Planning and Development what an SAH unit must be before you plan on the higher figure.

MF-3(A) and MF-4(A). These are the tall districts. MF-3(A) allows 90 homes per net acre, a floor area ratio of 2.0 (total floor area twice the lot area), 90 feet of height and a 6,000 square foot minimum lot. MF-4(A) allows 160 per net acre, a ratio of 4.0, 240 feet and 80 percent coverage. Both need 20-foot side and rear yards next to or across an alley from the residential districts named in the summary, and the part of a building over 45 feet sets back an extra 20 feet in front and one extra foot at the sides and rear for each two feet above 45, up to 30 feet in total.

Parking for Apartments Since May 2025

Ordinance No. 33112, passed May 14, 2025, rewrote the multifamily parking rule in Sec. 51A-4.209(b)(5)(C). It requires "None" for "multifamily developments with 20 dwelling units or less," "One half space per dwelling unit" for "more than 20 but less than 200 dwelling units," and one space per unit at 200 or more. "No additional parking is required for accessory uses that are limited principally to residents."

Multifamily development Required spaces Guest spaces
20 units or fewer None None
21 to 99 units One-half space per unit 10 percent of required spaces marked for guests
100 to 199 units One-half space per unit 15 percent of required spaces marked for guests
200 units or more One space per unit 15 percent of required spaces marked for guests

Source: Sec. 51A-4.209(b)(5)(C) as amended by Ordinance No. 33112. No minimum applies to any use with part of its lot within 2,640 feet of a light rail or streetcar station (Sec. 51A-4.301(a)(2)(B)).

A building of 150 units or more needs one loading space for a moving van, outside any gate. For a mixed income housing development, Sec. 51A-4.1107(c)(2) now reads: "Multifamily parking. No parking is required." Where parking is built, "In an MF-1(A), MF-1(SAH), MF-2(A), or MF-2(SAH) district, no required or excess parking may be placed in the required front yard," while in MF-3(A) and MF-4(A) it may extend to the front property line. If the City treats a small triplex or fourplex in an MF district as multifamily, it needs no parking under these rules.

SB 840: Apartments on Commercial Land

SB 840 created Local Government Code chapter 218. It applies to "a municipality with a population greater than 150,000 that is wholly or partly located in a county with a population greater than 300,000," which includes Dallas. A city "shall allow" multifamily or mixed use housing "in a zoning classification that allows office, commercial, retail, warehouse, or mixed-use use or development," and may not require a rezoning, variance, special exception or "other discretionary approval" first.

Section 218.102 sets the floor for what the City may require. Density may not be capped below "the greater of: (i) the highest residential density allowed in the municipality; or (ii) 36 units per acre." Height may not be capped below the commercial height on the site or 45 feet, whichever is greater. A setback may not exceed the commercial setback on the site or 25 feet, whichever is less. The City may not require "more than one parking space per dwelling unit," a multilevel parking structure, or a floor area ratio limit. The highest density in the City's residential summaries is 160 homes per net acre in MF-4(A); VanPlex did not check the planned development or central area districts.

Dallas wrote SB 840 into its permit rules. Ordinance No. 33192, passed August 27, 2025, lists exceptions in Chapter 52, Sec. 302.2.1: "A permit may be granted for a multifamily use or mixed use development, even if not allowed by the underlying zoning, if the multifamily use or mixed use development complies with the requirements of Chapter 218 of the Texas Local Government Code." A second exception covers converting an office, retail or warehouse building to housing. Matching exceptions in Sec. 306.1 cover the certificate of occupancy, the City's permission to occupy a building.

The law leaves out "a zoning classification that allows heavy industrial use," land within 1,000 feet of an existing heavy industrial use, land within 3,000 feet of an airport or military base, and clear zones and accident potential zones. It also keeps the City's historic preservation rules. The Dallas multifamily rule of no parking for 20 units or fewer is already below the state cap of one space per unit, so the City rule applies. The SB 840 page has the statewide detail.

What Gets Built

The Census Bureau's 2025 permit file shows the gap between small and large buildings in Dallas. The City issued permits for 4 buildings of three or four units, holding 12 homes, against 346 buildings of five or more units holding 4,883 homes, 36 two-unit buildings and 2,026 one-unit buildings. ForwardDallas 2.0 records that the City Plan Commission "voted to classify multiplex use as a secondary use in the Community Residential and Small Town Residential Placetypes," which keeps those areas "predominantly single-family." A placetype is a category of land in the plan.

Best For

  • ✓ An MF-1(A) or MF-2(A) lot of 4,800 to 7,200 square feet, enough for a fourplex of two-bedroom units with no parking minimum.
  • ✓ A TH or CH site of half an acre or more, laid out as rows of up to eight attached houses.
  • ✓ A commercial or retail lot outside the SB 840 exclusions, where apartments need no rezoning.

Usually Fails When

  • ✕ The site is zoned single-family or D and the plan assumes a triplex by right.
  • ✕ The plan counts on the SAH density figures without knowing what an SAH unit must be.
  • ✕ The commercial lot is within 3,000 feet of an airport or 1,000 feet of heavy industry.

What To Verify Before Spending Money

  • → Whether the City treats your triplex or fourplex as a multifamily use, with zoning staff.
  • → Any planned development ordinance on the site, which replaces the general district numbers.
  • → Whether the commercial zoning on your lot allows heavy industrial use, which removes it from SB 840.

Where to Go Next

Related on VanPlex: the Dallas overview and the SB 840 page.

Frequently Asked Questions

Where can I build a fourplex in Dallas? +
A fourplex in Dallas fits the districts whose City summaries list multifamily as a primary use: CH, MF-1(A), MF-2(A), MF-3(A) and MF-4(A). On land zoned for office, commercial, retail, warehouse or mixed use, SB 840 also requires the City to allow three or more homes, and Ordinance No. 33192 lets the building official issue that permit. A single-family or duplex lot needs a rezoning first.
How big a lot does a Dallas fourplex need? +
In MF-2(A), four two-bedroom apartments need 4,800 square feet of lot by VanPlex count, since the City summary sets 1,200 square feet per two-bedroom unit. In MF-1(A) the same fourplex needs 7,200 square feet, at 1,800 per unit. In the CH district four homes need 8,000 square feet, at 2,000 per home, within a cap of 18 homes per net acre.
Does a small Dallas apartment building need parking? +
No minimum applies to a Dallas multifamily development of 20 dwelling units or fewer since Ordinance No. 33112 of May 14, 2025. A development of 21 to 199 units needs one-half space per unit and one of 200 units or more needs one space per unit. Guest spaces are 10 percent of required parking for 21 to 99 units and 15 percent for 100 or more.
What is the difference between the TH-1(A), TH-2(A) and TH-3(A) districts in Dallas? +
The three Dallas townhouse districts differ in density. TH-1(A) allows no more than 6 homes per acre, TH-2(A) allows 9 and TH-3(A) allows 12. Each sets a 2,000 square foot lot for a house and 6,000 for a duplex, a 36-foot height limit, no minimum front yard and 60 percent lot coverage, with up to 80 percent on one lot when the project stays at 60.
How many attached homes can be in one Dallas townhouse row? +
In the Dallas townhouse and multifamily districts a plat must leave 15 feet between groups of eight single family structures, by the City TH, MF-1 and MF-2 summaries. In the CH district, "No group of attached dwelling units may exceed eight in number." The 2018 single-family rules add that each attached home needs separate utility services and a deed restriction for each shared wall.
What does SB 840 allow on Dallas commercial land? +
SB 840, now Local Government Code chapter 218, requires Dallas to allow multifamily or mixed use housing on land zoned for office, commercial, retail, warehouse or mixed use, with no rezoning or special approval. The City may not cap density below the greater of its highest residential density or 36 units per acre, cap height below 45 feet, or require more than one parking space per unit.
Which Dallas land does SB 840 leave out? +
SB 840 leaves out Dallas land in a zoning classification that allows heavy industrial use, land within 1,000 feet of an existing heavy industrial use, land within 3,000 feet of an airport or military base, and an area the City designates as a clear zone or accident potential zone. Ordinance No. 33192 applies the permit exception only where a project complies with Local Government Code chapter 218.
What is an MF-2(SAH) district in Dallas? +
MF-2(SAH) is a version of the Dallas MF-2 multifamily district in which the density cap rises with the share of "SAH Units Provided," by the City summary: 20 homes per net acre with none, 22 with 5 percent, 24 with 10 percent, 30 with 15 percent and 40 with 20 percent. MF-2(A), the other version, has no density cap and counts homes by lot area.
How tall can an apartment building be in Dallas? +
Dallas MF-1(A) and MF-2(A) allow 36 feet, MF-3(A) allows 90 feet and MF-4(A) allows 240 feet, by the City district summaries. In MF-3(A) and MF-4(A) the part of a building over 45 feet must step back an extra 20 feet from the front, and one extra foot from the side and rear for each two feet of height above 45, up to a total of 30 feet.
How many triplexes and fourplexes does Dallas permit each year? +
Dallas issued permits for 4 buildings of three or four units, holding 12 homes, in 2025, by the Census Bureau Building Permits Survey. In the same year it permitted 36 two-unit buildings, 346 buildings of five or more units holding 4,883 homes, and 2,026 one-unit buildings. Most new Dallas housing in buildings of three or more units comes in large apartment buildings.

Official sources (checked October 2026)

City of Dallas Current Planning, TH-1(A) district summary
https://dallascityhall.com/departments/sustainabledevelopment/planning/Pages/TH1.aspx
City of Dallas Current Planning, TH-2(A) district summary
https://dallascityhall.com/departments/sustainabledevelopment/planning/Pages/TH2A.aspx
City of Dallas Current Planning, TH-3(A) district summary
https://dallascityhall.com/departments/sustainabledevelopment/planning/Pages/TH3A.aspx
City of Dallas Current Planning, CH district summary
https://dallascityhall.com/departments/sustainabledevelopment/planning/Pages/CH.aspx
City of Dallas Current Planning, MF-1(A) and MF-1(SAH) district summary
https://dallascityhall.com/departments/sustainabledevelopment/planning/Pages/MF1andMF1SAH.aspx
City of Dallas Current Planning, MF-2(A) and MF-2(SAH) district summary
https://dallascityhall.com/departments/sustainabledevelopment/planning/Pages/MF2AandMF2sah.aspx
City of Dallas Current Planning, MF-3(A) district summary
https://dallascityhall.com/departments/sustainabledevelopment/planning/Pages/MF3A.aspx
City of Dallas Current Planning, MF-4(A) district summary
https://dallascityhall.com/departments/sustainabledevelopment/planning/Pages/MF4A.aspx
City of Dallas, Ordinance No. 30930 (Sec. 51A-4.209, June 27, 2018, PDF)
https://dallascityhall.com/departments/sustainabledevelopment/planning/DCH%20Documents/code%20amendments/ADUs/30930_BDA_ADU_Ord.PDF
City of Dallas, Ordinance No. 33112 (parking and loading, May 14, 2025, PDF)
https://citysecretary2.dallascityhall.com/resolutions/2025/05-14-25/25-0763.pdf
City of Dallas, Ordinance No. 33192 (Chapter 52 permits, August 27, 2025, PDF)
https://citysecretary2.dallascityhall.com/resolutions/2025/08-27-25/25-1335.pdf
City of Dallas, ForwardDallas 2.0
https://dallas.gov/departments/pnv/Forward-Dallas/Pages/default.aspx
Local Government Code chapter 218 (SB 840)
https://statutes.capitol.texas.gov/Docs/LG/htm/LG.218.htm#218.002
Census Bureau Building Permits Survey, South Region places, 2025
https://www2.census.gov/econ/bps/Place/South%20Region/so2025a.txt
VanPlex newsletter

Get new guides by email

New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.

General information, not legal advice. Texas has no statewide zoning code. Each city writes its own rules, and deed restrictions recorded on a lot can forbid what the city allows. Confirm current requirements with the city planning department, read the deed restrictions for your lot, and talk to a Texas-licensed attorney or architect before you buy land or file plans.

Planning a multiplex in Dallas?

VanPlex builds multiplexes in British Columbia, Canada. For a lot in Dallas, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.

Get a proforma for your address