Dallas | Zoning Districts
Dallas Residential Zoning Districts and How Many Homes Each Allows
Dallas zoning sorts land into districts, and the district decides how many homes a lot can hold. The City has seven single-family districts, where the rule is one home per lot. More homes are allowed in the duplex, townhouse, clustered housing and multifamily districts. This page lists each district with its lot size, its home count and its height, and explains how a rezoning works. The Dallas overview gives the short version.
Dallas zoning in six facts
- The City lists seven single-family districts, from R-1ac(A) to R-5(A), plus duplex, townhouse, clustered housing, multifamily, agricultural and mobile home districts. Source: City of Dallas, Zoning 101
- On a lot used for a single-family home, the Development Code allows one dwelling unit unless the Board of Adjustment grants a special exception. Source: Board of Adjustment case report, February 17, 2026
- The smallest single-family lot is 5,000 square feet in R-5(A); a duplex lot in the D district needs 6,000 square feet. Source: City of Dallas, R-5(A) and D district summaries
- Townhouse districts TH-1(A), TH-2(A) and TH-3(A) allow 6, 9 and 12 homes per acre; the CH district allows 18 per net acre. Source: City of Dallas, TH and CH district summaries
- A straight zoning change on up to one acre costs $1,050 and requires mailed notice to owners within 200 feet. Source: Ordinance No. 33265, October 22, 2025
- Under state law, a protest by owners of 60 percent of the land within 200 feet is needed before a change that only adds homes requires more than a majority vote. Source: Local Government Code 211.0061
Where These Rules Come From
The zoning law of Dallas is the Dallas Development Code, which is Chapter 51A of the City code. The City publishes that code through an outside code publisher whose website refused every request VanPlex sent, so this guide reads the rules from documents on the City's own websites. There are three kinds.
- District summary pages. The Planning and Development Department keeps one page for each residential district. Each says: "The attached documents list the general guidelines to the Yard, Lot and Space Regulations. There may be exceptions to this information. See 51A-4.100 of the Dallas Development Code for specific details."
- Signed ordinances. When the City Council changes the code, the ordinance prints the new wording of each section it changes. The City Secretary posts the signed copies, and this guide names the ordinance behind each rule.
- Case reports. Board of Adjustment and City Plan Commission staff quote the code section that applies in each case report, and the reports are attached to the City's Council records.
A summary page is a guide written by City staff. Where a summary and an ordinance disagree, the ordinance is the law. Before you buy land or file a plan, ask the City's zoning staff to confirm the rules for your lot; the summary pages give the Building Inspection number 214-948-4480 for that.
The Residential Districts
The City's Zoning 101 presentation lists the base residential districts: one agricultural district, A(A); seven single-family districts; one duplex district, D; three townhouse districts; one clustered housing district, CH; four multifamily districts, MF-1 to MF-4; and one mobile home district, MH(A). The City's page for R-7.5(A) calls it the "Single Family 7,500 Square Feet District," and the other single-family names follow the same pattern. Density means the number of homes allowed on an acre of land; the summaries for CH, MF-3(A) and MF-4(A) count it per net acre.
| District | Minimum lot for homes | Homes allowed | Height limit |
|---|---|---|---|
| R-1ac(A) | 1 acre | One home per lot | 36 ft |
| R-1/2ac(A) | 1/2 acre | One home per lot | 36 ft |
| R-16(A) | 16,000 sq ft | One home per lot | 30 ft |
| R-13(A) | 13,000 sq ft | One home per lot | 30 ft |
| R-10(A) | 10,000 sq ft | One home per lot | 30 ft |
| R-7.5(A) | 7,500 sq ft | One home per lot | 30 ft |
| R-5(A) | 5,000 sq ft | One home per lot | 30 ft |
| D (duplex) | 6,000 sq ft | A duplex (two homes) or one house | 36 ft |
| TH-1(A), TH-2(A), TH-3(A) | 2,000 sq ft per house; 6,000 sq ft per duplex | 6, 9 or 12 homes per acre | 36 ft |
| CH (clustered housing) | 2,000 sq ft per home | 18 homes per net acre, groups of 8 or fewer | 36 ft |
| MF-1(A), MF-2(A) | Set per home, by bedrooms | No density cap; lot area per home sets the count | 36 ft |
| MF-3(A) | 6,000 sq ft | 90 homes per net acre | 90 ft |
| MF-4(A) | 6,000 sq ft | 160 homes per net acre | 240 ft |
Source: City of Dallas Current Planning district summary pages, read October 9, 2026 (each district name links to its page). The one-home-per-lot entries in the single-family rows come from the single-family use rule quoted in Board of Adjustment case reports, since each single-family summary lists "No maximum dwelling unit density."
The City's documents do not agree on one name. Zoning 101 lists an "R-15(A)" district, while the City's district page is titled "R16(A) - Single Family 16,000 Square Feet District" and sets a 16,000 square foot minimum lot. The district page gives the full set of yard and lot rules; confirm the name and the lot size on the City's zoning map for your lot.
One Dwelling Unit per Lot
The single-family summaries say "No maximum dwelling unit density," yet a single-family lot holds one home. The limit comes from the use rules. A use is the activity on a lot, such as a single-family home or a duplex, and Dallas sets rules for each use in Division 51A-4.200. Board of Adjustment staff state the single-family rule in their February 17, 2026 case report: "The Dallas Development Code states that only one dwelling unit may be located on a lot."
The same rule applies in other districts when the use is a single-family home. The February 2026 report on 802 W. Greenbriar Lane describes a lot zoned CD-13, a conservation district, "which limits the number of dwelling units to one." The Board of Adjustment is a City board that hears requests to depart from the zoning rules on one property. It can grant a special exception, which is a permission the code allows the Board to give when set tests are met. Two special exceptions add a home to a single-family lot, and the ADU and duplex page covers both.
The electric service follows the same pattern. Each single-family summary says a lot for a single family use "may be supplied by not more than one electrical utility service, and metered by not more than one electrical meter." On the D district page, a lot for a duplex use may have one service and "not more than two electrical meters." The Board can approve more meters by special exception when they will "not be used to conduct a use not permitted in this district."
Duplex, Townhouse and Clustered Housing Districts
D (duplex). The D district summary lists "Duplex dwelling" as the primary use. A duplex is one building with two homes. The minimum lot for residential use is 6,000 square feet, the height limit is 36 feet, and buildings may cover up to 60 percent of the lot.
TH-1(A), TH-2(A) and TH-3(A) (townhouse). A townhouse is a house on its own small lot, which can share walls with its neighbors. The three districts differ in density: TH-1(A) allows "No more than 6 dwelling units for each acre," TH-2(A) allows 9 and TH-3(A) allows 12. Each sets a 2,000 square foot lot for a single-family structure and 6,000 square feet for a duplex structure, with no minimum front yard. One lot may be 80 percent covered "if the coverage for the total project does not exceed 60% and at least 40% is reserved for open space." A plat must leave 15 feet between groups of eight houses.
CH (clustered housing). The CH summary lists "Single Family, Duplex, Residential and Multifamily" as primary uses. Density is capped at 18 homes per net acre, each home needs 2,000 square feet of lot, and "No group of attached dwelling units may exceed eight in number." The district itself must cover at least one-half acre unless the City Council finds a smaller district is justified "in a transitional circumstance separating a residential district from a higher density district."
Multifamily Districts
Multifamily means a building or site with several homes, such as an apartment building. The four MF districts count homes in two ways. MF-1(A) and MF-2(A) have "No maximum dwelling unit density" but set a minimum lot area for each home, so a bigger lot allows more homes. MF-3(A) and MF-4(A) add a density cap and a floor area ratio (FAR), which is the total floor area of the buildings divided by the lot area.
- MF-1(A): each multifamily home needs 1,000 square feet of lot with no separate bedroom, 1,400 with one bedroom, 1,800 with two, and 200 more for each bedroom over two. Height is 36 feet.
- MF-2(A): the same steps are 800, 1,000 and 1,200 square feet, plus 150 for each bedroom over two. Height is 36 feet.
- MF-3(A): 90 homes per net acre, FAR 2.0, a 90-foot height limit and a 6,000 square foot minimum lot.
- MF-4(A): 160 homes per net acre, FAR 4.0, a 240-foot height limit and 80 percent lot coverage.
MF-1 and MF-2 each have a second version marked SAH. In an SAH district the density cap rises with the share of units the summary calls "SAH Units Provided": in MF-1(SAH), from 15 homes per net acre with none to 30 with 20 percent; in MF-2(SAH), from 20 to 40. The townhouse and multifamily page works through what these numbers mean for a triplex or fourplex.
Planned Development, Conservation and Form Districts
Some Dallas lots sit in other kinds of base district. Zoning 101 names four kinds of base zoning: general or "straight" zoning, such as R-7.5(A); planned development districts, such as "PD No. 193, PD No. 595, PD No. 887"; conservation districts, such as "M Streets, Bishop Arts"; and form districts, such as "WMU-20, RTN, WR-5." A planned development district "tailors the uses and development regulations for an area," and a conservation district "conserves an area's distinctive character by protecting or enhancing its physical attributes and architecture." Form districts, in the same presentation, "create walkable, mixed use developments based on scale and building type, and street front design standards."
Each of these has its own ordinance, so the summaries above do not decide what such a lot allows. A February 2026 Board of Adjustment report shows a lot with two layers: it is zoned "PD-595 (R-5(A)) and H/100," and the report names the second layer the "Wheatley Place Historic District (Overlay)." An overlay adds rules to the base district under it; the conservation and overlay page covers them.
Changing the Zoning on a Lot
A rezoning in Dallas goes to two public hearings. The City Plan Commission (CPC), a board of residents appointed by the Council, holds the first and sends a recommendation; the City Council holds the second and decides. The April 7, 2026 committee packet prints Sec. 51A-4.701 with its notice rules: notice in the official newspaper at least 10 days before the CPC hearing, and letters to owners nearby, mailed at least 10 days before the CPC hearing and 15 days before the Council hearing. The letter "must be written in English and Spanish" where the census tract is 50 percent or more people of Spanish origin. For an owner's own application, the section points to the fee table in Sec. 51A-1.105 for the notice area, shown below.
| Straight zoning change, area of request | Application fee | Mailed notice area |
|---|---|---|
| 0 to 1 acre | $1,050 | 200 feet |
| Over 1 acre to 5 acres | $2,610 | 300 feet |
| Over 5 acres to 15 acres | $5,820 | 400 feet |
| Largest fee for a straight zoning change | $37,500 | Not stated |
Source: Sec. 51A-1.105(a)(4) as restated by Ordinance No. 33265, passed October 22, 2025.
Protests. State law sets two protest routes, and the Dallas code text still differs from them. Under Local Government Code 211.0061, in force since September 1, 2025, owners of "at least 20 percent of the area of the lots or land covered by the proposed change" can force a vote of three-fourths of all members of the Council, for any change. For a change that "has the effect of allowing more residential development" and adds no commercial or industrial use beyond a limited ground floor, a protest by the adjoining land within 200 feet needs "at least 60 percent" of that land, and the change then needs "a majority of all members." City staff wrote in the April 2026 packet that the Dallas code "currently requires that a change in zoning regulations or district boundaries that has been protested according to certain thresholds must be approved by three-fourths of the City Council rather than the typical majority." Where the two differ, the statute controls.
Staff proposed amendment DCA 256-004 to bring the code in line, with three tiers of Council vote. The minutes of April 7, 2026 show the Zoning Ordinance Advisory Committee voted 7 to 2 to forward it to the CPC, "except only requiring the posting of zoning change signs no later than the fifteenth day before a city plan commission, landmark commission, or board of adjustment hearing." The City's code amendments page lists every committee meeting from June 9 to November 3, 2026 as cancelled, and VanPlex found no Council vote on the amendment in the City's records.
The plan behind the zoning. ForwardDallas 2.0, adopted September 25, 2024 and amended in March 2026, guides these cases. The City says it "does not allow multiplexes on any single-family zoned property in Dallas," and that the CPC "voted to classify multiplex use as a secondary use in the Community Residential and Small Town Residential Placetypes." A placetype is a land category in the plan. A multiplex on a single-family lot still needs a rezoning case.
Best For
- ✓ A lot already zoned D, TH, CH or MF, where more than one home is allowed without a rezoning.
- ✓ A large MF-1(A) or MF-2(A) lot, where the lot area per home sets the count and there is no density cap.
- ✓ A rezoning on land under one acre, where the fee is $1,050 and notice goes to owners within 200 feet.
Usually Fails When
- ✕ The lot is in a single-family district and the plan counts on a second home without a Board approval.
- ✕ The lot is in a planned development or conservation district and the plan uses the general district numbers.
- ✕ A rezoning schedule assumes the City code protest rules, which state law changed in 2025.
What To Verify Before Spending Money
- → The exact district, any PD or overlay, and the current text of Chapter 51A, with Building Inspection (214-948-4480).
- → Whether amendment DCA 256-004 on notices and protests has been adopted.
- → The fee table in force on the day you file, since the City restates Sec. 51A-1.105 when it changes fees.
Where to Go Next
Related on VanPlex: the Dallas overview, how Texas zoning works, and the HB 24 protest page.
Frequently Asked Questions
How many homes can I build on a single-family lot in Dallas?
What is the smallest single-family zoning district in Dallas?
Which Dallas zoning districts allow a duplex?
How many homes can a Dallas townhouse district hold?
What is a planned development district in Dallas?
How much does it cost to rezone a lot in Dallas?
Can neighbors force a supermajority vote on a Dallas rezoning?
Has Dallas updated its own zoning protest rules for HB 24?
How many homes per acre do Dallas multifamily districts allow?
Does ForwardDallas 2.0 change the zoning on my Dallas lot?
Official sources (checked October 2026)
Get new guides by email
New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.
Planning a multiplex in Dallas?
VanPlex builds multiplexes in British Columbia, Canada. For a lot in Dallas, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.
Get a proforma for your address