David Babakaiff
Written by David Babakaiff · Co-Founder, VanPlex | 25+ Years BC Construction Last reviewed: October 2026

Los Angeles | Hillside and Fire Zones

Los Angeles Hillside and Fire Zones: Slope-Based Floor Area, Grading and Fire Zone Limits

Two map layers change what a Los Angeles lot can hold. The Hillside Area, drawn on the City Planning Hillside Area Map, brings its own floor area, grading, height and parking rules for single-family zones. A Very High Fire Hazard Severity Zone limits ADUs, small-lot maps and the City's transit bonus. Where the two overlap, the City calls the land a Fire Restriction Area. This page gives the rules for each. The Los Angeles overview lists the state laws they modify.

Hillside and fire rules in six facts

  • On an R1, RS, RE or RA lot in the Hillside Area, maximum residential floor area is the sum of each slope band area times its floor area ratio, from 0.45 on R1 land under 15 percent slope to 0 on slopes of 100 percent or more. Source: LAMC 12.21 C.10(b), Ord. 184,802
  • Every Hillside Area R1 lot is guaranteed residential floor area of at least 25 percent of the lot or 800 square feet, whichever is greater. Source: LAMC 12.21 C.10(b)(2), Ord. 184,802
  • By-right grading on a Hillside Area R1 lot is capped at 1,000 cubic yards, and earth may be trucked in or out only from 9 a.m. to 3 p.m. on weekdays. Source: LAMC 12.21 C.10(f), Ord. 184,802
  • LAMC 12.22 A.33(c)(4) bars ADUs on lots in both a Very High Fire Hazard Severity Zone and a Hillside Area, and City Planning does not enforce that bar on state-law ADUs. Source: ZA Memo 143, Q.42
  • The Starter Home Revitalization Act cannot be used in high or very high fire hazard severity zones, and the Low-Rise Ordinance excludes Fire Restriction Areas. Source: LA City Planning, SHRA memo
  • LAFD says CAL FIRE issued recommended fire hazard severity zone maps for the City on March 24, 2025, and that state law requires the City to adopt them by ordinance. Source: LAFD notice

The Hillside Area Rules and Where They Come From

The rules sit in LAMC 12.21 C.10. The City first adopted them as the Baseline Hillside Ordinance (No. 181,624) in 2011 "to address the same issue of out-of-scale development in hillside neighborhoods by establishing regulations for projects in the hillside areas, including limitations on residential floor area and the amount of allowable grading based on lot size," as the opening of Ordinance No. 184,802 recalls. That 2017 ordinance rewrote them. They apply "for any Lot zoned R1, RS, RE or RA and designated Hillside Area on the Department of City Planning Hillside Area Map," to new buildings, additions and any "Major Remodel-Hillside."

Multifamily zones follow different hillside rules. The City Planning summary notes that height for the A1, A2 and RD zones is "limited to 36 ft or 45 ft in Hillside Areas in accordance with Section 12.21 A.17," and that the R1H variation zones follow the R1 Hillside Area standards with their own floor area ratios. A Hillside designation can also change the minimum lot size in the RA and RE zones.

Hillside Setbacks

Table 12.21 C.10-1 sets the yards for single-family Hillside Area lots. The front yard rule also sets bounds: nothing in it requires "Front Yards which exceed 40 feet in depth" or allows "Front Yards that are less than 5 feet in depth."

Yard R1 Other single-family zones
Front yard At least 20% of lot depth, need not exceed 20 ft At least 20% of lot depth, need not exceed 25 ft (RS, RE, RA)
Side yard 5 ft (R1 and RS) 7 ft (RE9, RE11); 10% of lot width, 5 to 10 ft (RE15); 10 ft (RE20, RE40, RA)
Side yard, taller buildings 1 more foot for each 10 feet of height above the first 18 feet Same
Side wall over 14 ft high and 45 ft long Offset at least 5 ft deep and 10 ft long Not listed in the table
Rear yard 15 ft (R1); 20 ft (RS) 25% of lot depth, need not exceed 25 ft (RE, RA)

Source: Ordinance No. 184,802, Table 12.21 C.10-1. The side yard may drop to 10 percent of lot width, at least 3 feet, on R1 and RS lots under 50 feet wide, RE9 and RE11 lots under 70 feet wide, and RA lots of record before July 1, 1966 under 70 feet wide.

Some front yard features are allowed on steep lots. "A detached Private Garage may be located on the required Front Yard of a Lot where the Elevation of the ground at a point 50 feet from the front Lot line" differs from the curb by 10 feet or more, if every part of the garage is at least 5 feet from the front lot line. Balconies with 10 feet of clearance below may project 30 inches into the front yard. In R1, an occupied rooftop deck must sit at least 3 feet back from the side yard.

Floor Area by Slope Band

On flat land, R1 floor area is a single ratio of the lot. On a Hillside Area lot it depends on the slope. The rule: "The maximum Residential Floor Area contained in all Buildings and Accessory Buildings shall not exceed the sum of the square footage of each Slope Band multiplied by the corresponding Residential Floor Area Ratio (RFAR) for the zone of the Lot." A slope band is the part of the lot whose ground slopes within a set range, such as 15 to 29.99 percent; a 100 percent slope rises one foot for each foot across.

Slope band R1 RS RE9, RE11 RE15, RE20, RE40 RA
0 to 14.99% 0.45 0.45 0.40 0.35 0.25
15 to 29.99% 0.45 0.40 0.35 0.30 0.20
30 to 44.99% 0.40 0.35 0.30 0.25 0.15
45 to 59.99% 0.35 0.30 0.25 0.20 0.10
60 to 99.99% 0.30 0.25 0.20 0.15 0.05
100% or more 0.00 0.00 0.00 0.00 0.00

Residential floor area ratio for each slope band. Source: Ordinance No. 184,802, Table 12.21 C.10-2a.

The applicant proves the slope with a Slope Analysis Map "prepared, stamped and signed by a registered civil engineer or licensed land surveyor," drawn at a scale of at least 1 inch to 100 feet with contours no more than 10 feet apart. City Planning approves the calculated maximum before LADBS takes the permit. As an example by VanPlex arithmetic, an R1 lot of 8,000 square feet with 4,000 square feet under 15 percent slope and 4,000 square feet at 30 to 44.99 percent allows 1,800 plus 1,600, or 3,400 square feet.

Two rules raise the figure. First, a guaranteed minimum: the maximum "may be at least the percentage of the Lot size as outlined in Table 12.21 C.10-3 below or 800 square feet, whichever is greater," with 25 percent for R1, 23 percent for RS, 20 percent for RE9 and RE11, 18 percent for RE15 to RE40 and 13 percent for RA. Second, in the RA, RE and RS zones (R1 is left out of this list), "An additional 20 percent" is allowed, or 30 percent where the guaranteed minimum is used, when the design uses one of six options, such as upper stories no larger than 75 percent of the base floor, a stepped-back front, wider side yards, an 18-foot envelope height, split buildings, or minimal grading. A Zoning Administrator may grant adjustments of up to 10 percent.

Height on a hillside lot is measured as "envelope height," the vertical distance from the Hillside Area grade to a plane parallel to the grade above, at every point of the building. In R1 the encroachment plane still starts 20 feet above grade along the front and side yards.

Grading Limits

Grading is moving earth: cut is earth removed and fill is earth added. LAMC 12.21 C.10(f) says "No Grading permits shall be issued until a Building permit is approved," and limits the total: "a base maximum of 1,000 cubic yards plus the numeric value equal to 10% of the total Lot size in cubic yards." The code's own example is a 5,000 square foot lot with a 1,500 cubic yard maximum. The total may never exceed the by-right figure for the zone:

Zone By-right grading maximum (cubic yards)
R1 1,000
RS 2,200
RE9 2,400
RE11 2,800
RE15 3,200
RE20 4,000
RE40 6,600
RA 3,600

Source: Ordinance No. 184,802, Table 12.21 C.10-6.

Earth import and export "may take place only between the hours of 9:00 a.m. and 3:00 p.m., Monday through Friday." On a lot fronting a Substandard Hillside Limited Street, a narrow hillside street class defined in LAMC 12.03, import and export combined is capped at 75 percent of the by-right figure. Grading for deep foundations such as caissons and piles, up to 500 cubic yards for a driveway, and remedial grading recommended by a geotechnical report are exempt from the caps. A Zoning Administrator may approve grading above the by-right figure, up to the formula amount. New graded slopes may be no steeper than 2 to 1, and grading on any slope of 100 percent or more needs the strictest level of geotechnical report and a deputy grading inspector on site, paid for by the owner.

Narrow Hillside Streets: Height and Parking

Lots on a Substandard Hillside Limited Street get two more rules. Height: "no portion of a Building or Structure within 20 feet of the Front Lot Line shall exceed 24 feet in height," measured from the center of the street. Parking: when the buildings "exceed a combined Residential Floor Area of 2,400 square feet, there shall be one additional parking," one space for each added 1,000 square feet or part of it, "for a maximum of five total on-site spaces." The added spaces need not be covered and may sit in the front yard. Stairways, porches and landings may not project into the front yard on these lots.

Street width also matters for City Ordinance ADUs. The fire zone exception in LAMC 12.22 A.33(c)(4) requires a street "improved with a roadway width of 20 feet or more in unobstructed width." ZA Memo 143 says dedications "may still be required for ordinance ADUs" in these areas, while state-law ADUs need no off-site improvements.

Very High Fire Hazard Severity Zones

Under Government Code 51178, "The State Fire Marshal shall identify areas in the state as moderate, high, and very high fire hazard severity zones," based on "fuel loading, slope, fire weather, and other relevant factors." The City's ADU ordinance refers to zones "designated by the City of Los Angeles Fire Department pursuant to Government Code Section 51178," and the fee ordinance to zones described in LAMC 57.4908.

The maps are changing. The LAFD notice says "On March 24, 2025, CAL FIRE issued the 2025 Recommended Fire Hazard Severity Zone (FHSZ) maps for Southern California, including the City of Los Angeles," that "a local agency shall not decrease the level of the FHSZ recommended by the State," and that "State law requires the City of Los Angeles to adopt the recommended maps by ordinance." LAFD expected more parcels to be affected. VanPlex did not find the City's adoption ordinance; check ZIMAS for the current designation of your lot.

Each housing path treats these zones in its own way:

Path Rule in a very high fire hazard severity zone Source
City Ordinance ADU Barred on lots in both a Very High Fire Hazard Severity Zone and a Hillside Area, with exceptions LAMC 12.22 A.33(c)(4)
State ADU (Gov. Code 66323) The bar is not enforced ZA Memo 143, Q.42
SB 9 two homes or lot split Allowed, subject to special building, fire or seismic rules City Planning SB 9 page
SHRA map of up to 10 lots Not allowed in high or very high fire hazard severity zones SHRA memo
Low-Rise Incentive Area Not allowed in a Fire Restriction Area (very high fire zone plus Hillside Area), with an edge-lot exception Ord. 188,967
SB 79 Temporarily exempt in a very high fire hazard severity zone, and paused citywide Ord. 188,968
Preliminary parcel map fee Surcharge of one-third of the map fee Ord. 188,796
Tentative tract map fee Surcharge of one-half of the map fee Ord. 188,796

Sources: Ordinance No. 186,481, ZA Memo 143, SB 9 page, SHRA memo, Ord. 188,967, Ord. 188,968, Ord. 188,796.

For City Ordinance ADUs, the bar applies only where the fire zone and the Hillside Area overlap, and it has exceptions: lots in the Northeast Los Angeles or Silver Lake - Echo Park - Elysian Valley Community Plan Areas, or ADUs with fire sprinklers, one parking space and a 20-foot street. ZA Memo 143 says the City "may not impose" terms that conflict with state law, naming the sprinkler, parking and off-site improvement terms. For SB 9, state law lets a project in a very high fire zone proceed when it meets fire mitigation standards; Government Code 65913.4(a)(6)(D) lists them, including Public Resources Code 4291 and 4290.

Best For

  • ✓ A Hillside Area lot mostly under 15 percent slope, which keeps the R1 ratio of 0.45.
  • ✓ A small steep lot where the guaranteed minimum of 25 percent or 800 sq ft beats the slope band result.
  • ✓ A state-law ADU on a fire zone hillside lot, which the City does not bar.

Usually Fails When

  • ✕ The plan needs more grading than the zone allows by right, such as over 1,000 cubic yards in R1.
  • ✕ The lot fronts a Substandard Hillside Limited Street and the front of the house tops 24 feet.
  • ✕ The plan relies on the SHRA or the Low-Rise Ordinance in a fire zone.

What To Verify Before Spending Money

  • → Fire zone status on the SB 9 or SHRA checklist in ZIMAS, and Hillside Area status and street class with City Planning.
  • → A Slope Analysis Map from a civil engineer or land surveyor.
  • → Whether the City has adopted the 2025 fire zone maps, which may add your lot.

Where to Go Next

Related on VanPlex: the Los Angeles overview, property tax and insurance and is your lot eligible.

Frequently Asked Questions

What is a Hillside Area in Los Angeles? +
A Hillside Area in Los Angeles is land shown on the Department of City Planning Hillside Area Map. Under LAMC 12.21 C.10, R1, RS, RE and RA lots on that map follow separate rules for setbacks, floor area by slope, height, grading and parking. The rules cover new buildings, additions and any Major Remodel-Hillside on those lots.
How is floor area calculated on a Los Angeles hillside lot? +
On a Los Angeles Hillside Area lot, a licensed civil engineer or land surveyor maps the lot into slope bands. Each band area is multiplied by its floor area ratio from Table 12.21 C.10-2a, and the results are added. For R1, the ratio runs from 0.45 on slopes under 15 percent to 0 on slopes of 100 percent or more.
What is the minimum house size allowed on a Los Angeles hillside lot? +
Los Angeles guarantees a minimum residential floor area on Hillside Area lots under LAMC 12.21 C.10(b)(2): 25 percent of the lot in R1, 23 percent in RS, 20 percent in RE9 and RE11, 18 percent in RE15 to RE40 and 13 percent in RA, or 800 square feet, whichever is greater. It applies in place of the slope band result.
How much grading can I do on a hillside lot in Los Angeles? +
On a Los Angeles Hillside Area lot, total grading is capped at 1,000 cubic yards plus 10 percent of the lot size in cubic yards, and never more than the by-right figure for the zone: 1,000 cubic yards in R1, 2,200 in RS and up to 6,600 in RE40. A Zoning Administrator may approve more, up to the formula amount.
What is a Substandard Hillside Limited Street in Los Angeles? +
It is a narrow hillside street class defined in LAMC 12.03. On a Los Angeles lot fronting one, no part of a building within 20 feet of the front lot line may exceed 24 feet in height, measured from the street, and earth import and export is capped at 75 percent of the by-right grading figure. Larger homes need extra parking.
Do hillside homes need extra parking in Los Angeles? +
Yes, on a Substandard Hillside Limited Street. Under LAMC 12.21 C.10(g), when the buildings on such a Los Angeles lot exceed 2,400 square feet of residential floor area, one more parking space is required for each additional 1,000 square feet or part of it, up to five spaces in total. These added spaces need not be covered.
Can I use SB 9 in a very high fire hazard severity zone in Los Angeles? +
Yes, subject to added rules. Los Angeles City Planning says lots in a Very High Fire Hazard Severity Zone are eligible for SB 9 but subject to special building, fire or seismic code requirements listed on the SB 9 checklist in ZIMAS. State law requires adopted fire hazard mitigation measures for such sites under Government Code 65913.4(a)(6)(D).
Can I build up to 10 starter homes on a lot in a Los Angeles fire zone? +
No. The Los Angeles SHRA memo of October 28, 2025 lists high or very high fire hazard severity zones among the sites where a Starter Home Revitalization Act project may not be located, for both state and local responsibility areas. A lot outside those zones may use the SHRA for up to 10 lots and 10 homes.
Has Los Angeles adopted the 2025 fire hazard severity zone maps? +
LAFD said in April 2025 that CAL FIRE issued recommended Fire Hazard Severity Zone maps for the City of Los Angeles on March 24, 2025, that LAFD was aligning them to streets and property lines, and that state law requires the City to adopt them by ordinance after public hearings. VanPlex did not find the adoption record; check ZIMAS for your lot.
Does a hillside lot cost more to subdivide in Los Angeles? +
In a Very High Fire Hazard Severity Zone it does. Ordinance No. 188,796 adds a surcharge of one-third of the City Planning fee to a preliminary parcel map, one-half to a tentative tract map, and 50 percent to the Bureau of Engineering final parcel map fee. A Hillside Area map also needs a report from the Superintendent of Building.

Official sources (checked October 2026)

Ordinance No. 184,802, Hillside Area rules in LAMC 12.21 C.10 (PDF)
https://cityclerk.lacity.org/onlinedocs/2014/14-0656_ORD_184802_3-13-17.pdf
LA City Planning, Generalized Summary of Zoning Regulations (PDF)
https://planning.lacity.gov/odocument/eadcb225-a16b-4ce6-bc94-c915408c2b04/Zoning_Code_Summary.pdf
Ordinance No. 186,481, ADU ordinance (PDF)
https://cityclerk.lacity.org/onlinedocs/2016/16-1468_ORD_186481_12-19-2019.pdf
ZA Memo 143, Revision 1 (PDF)
https://planning.lacity.gov/odocument/6bf1cc9b-0342-4852-ae4c-646d46953d5c/ZA_Memo_143_Revision_1_Chapter1_8.1.25.pdf
LA City Planning, Senate Bill 9
https://planning.lacity.gov/project-review/senate-bill-9
LA City Planning, SHRA implementation memo (PDF)
https://planning.lacity.gov/odocument/1b081b86-f735-43e8-bba6-c2d73a192db7/SB_684_1123_Memo_Update_ACP.pdf
Ordinance No. 188,967, Low-Rise Ordinance (PDF)
https://cityclerk.lacity.org/onlinedocs/2025/25-1083-S3_ord_188967_06-30-26.pdf
Ordinance No. 188,968, SB 79 Phased Implementation Ordinance (PDF)
https://cityclerk.lacity.org/onlinedocs/2025/25-1083-S4_ord_188968_06-30-26.pdf
Ordinance No. 188,796, City Planning fees (PDF)
https://planning.lacity.gov/odocument/1610be5a-24d8-4e94-8e35-3df61426141d/Ordinance_188796_with_Director_Memo.pdf
LAFD, 2025 Fire Hazard Severity Zones map recommendation
https://lafd.org/news/2025-cal-fire-fire-hazard-severity-zones-map-recommendation
Government Code 51178 (fire hazard severity zones)
https://leginfo.legislature.ca.gov/faces/codes_displaySection.xhtml?lawCode=GOV&sectionNum=51178
Government Code 65913.4 (sites excluded from streamlining)
https://leginfo.legislature.ca.gov/faces/codes_displaySection.xhtml?lawCode=GOV&sectionNum=65913.4
VanPlex newsletter

Get new guides by email

New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.

General information, not legal advice. California housing law changes every year, and each city adds its own rules on top of state law. Confirm current requirements with the city or county planning department, and with a California-licensed attorney or architect, before you buy land or file plans.

Planning a multiplex in Los Angeles?

VanPlex builds multiplexes in British Columbia, Canada. For a lot in Los Angeles, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.

Get a proforma for your address