David Babakaiff
Written by David Babakaiff · Co-Founder, VanPlex | 25+ Years BC Construction Last reviewed: October 2026

Los Angeles | Zoning Districts

Los Angeles Zoning Districts: How Many Homes Each Zone Allows

Every lot in the City of Los Angeles carries a zone, and the zone sets the starting count of homes. This page lists the residential zones, the lot size each one needs, and the number of homes each allows, from the City Planning Generalized Summary of Zoning Regulations (updated January 2026) and the zoning ordinances behind it. State laws can add homes on top of the zone; the Los Angeles overview lists them.

Los Angeles zoning in six facts

Two Zoning Codes in One City

Los Angeles has two zoning codes at the same time. Chapter 1 of the Los Angeles Municipal Code (LAMC) is the original code, with zone names such as R1 and RD2. Chapter 1A is a new code. City Planning's New Zoning Code page says the City "adopted a new Zoning Code (Chapter 1A of the LAMC) in October 2024" and that it "is applied in the Downtown Community Plan Area." The same page lists Boyle Heights, Harbor Gateway and Wilmington under "New Zoning Under Council Review" and says the "Existing Zoning Code will continue to apply in areas where an update has not occurred."

For most owners, then, Chapter 1 is the code. One part of Chapter 1A reaches every lot. The Chapter 1A book (Ordinance No. 188,418, effective January 20, 2025) says Article 13, its procedures article, "is the only Article in this Zoning Code (Chapter 1A) that applies to both Chapters." The permits and fees page uses those procedures.

The full text of both chapters is published on codelibrary.amlegal.com, which refused automated requests for this guide. The rules on this page come from the City Planning summary and from adopted ordinances posted by the City Clerk. The summary carries its own warning: "This summary is only a guide. Definitive information should be obtained from Chapter 1 of the Los Angeles Municipal Code (LAMC) itself." Where the summary and an adopted ordinance differ, the ordinance controls.

How to Read a Chapter 1 Zone

A Chapter 1 zone has up to four parts. The summary's example is [Q]C2-1-CDO. The middle part (C2) is the zone classification, which sets the allowed uses, the minimum lot area, the yards and the parking. The number after the first hyphen (1) is the height district, which sets floor area ratio and sometimes the number of stories or feet. Floor area ratio is the floor area of the buildings divided by the lot area. The last part (CDO, a Community Design Overlay) is a supplemental use district, which adds rules for one area.

Letters in brackets or after the height district are special classifications set by ordinance for that lot. In the summary's words, a Q (qualified classification) "Restricts uses allowed on property," a D (development limitation) "Restricts heights, floor area ratio, lot coverage, building setbacks," and a T is a tentative classification "pending certain required dedications, payments or improvements." Read the Council file or ordinance behind a Q or D before you design, because it can be stricter than the zone.

The summary lists 20 supplemental use districts. Several matter for small housing projects: RFA (Residential Floor Area District), HS (Hillside Standards Overlay), RG (Rear Detached Garage), HCR (Hillside Construction Regulation), CPIO (Community Plan Implementation Overlay) and K (Equinekeeping). It also lists Specific Plans such as Warner Center, Playa Vista and Park Mile, and the Historic Preservation Overlay Zone (HPOZ). A Specific Plan is a set of rules for one named area that can replace parts of the zone.

Single-Family Zones and Their Lot Sizes

The one-family zones are where most Los Angeles lots sit. Each one sets a minimum lot area and a minimum lot width for creating new lots. The summary lists one-family dwellings as the main use in each.

Zone Minimum lot area Minimum lot width
RE40 40,000 sq ft 80 ft
RE20 20,000 sq ft 80 ft
RA 17,500 sq ft 70 ft
RE15 15,000 sq ft 80 ft
RE11 11,000 sq ft 70 ft
RE9 9,000 sq ft 65 ft
RS 7,500 sq ft 60 ft
R1 5,000 sq ft 50 ft
RU 3,500 sq ft 35 ft
RZ2.5, RZ3, RZ4 2,500, 3,000 or 4,000 sq ft 30 ft with a driveway, 25 ft without
RW1 2,300 sq ft 28 ft

Source: LA City Planning, Generalized Summary of Zoning Regulations, Table 1a, CP-7150 (1.20.2026). RE40 and RE20 share the 80-foot width cell with RE15. A Hillside designation can change the RA and RE figures.

Two notes in the summary change the one-home rule at the edges. For the RA, RE, RS and R1 zones, note 14 says the zone "allows for two-family dwellings when adjoining commercial or industrial zones and qualifies under certain other lot location and area restrictions." For the A1 and A2 agricultural zones and the R2 zone, note 15 says "A maximum of two dwelling units are allowed per lot based on certain lot area regulations." The summary does not give the lot tests; read them in the LAMC section for the zone before relying on either note.

RU (Residential Urban), RZ (Residential Zero Side Yard) and RW1 (One-Family Residential Waterways) are small-lot one-family zones. RZ lots may have a zero side yard, which means the house can sit on the side lot line, and the summary lists a 2,300 square foot minimum lot for RW1. City Planning lists all of these zones, with A, RA, RE, RS and R1, as single-family zones for SB 9.

The R1 Zone and Its Four Variations

R1 is the most common one-family zone. Ordinance No. 184,802, in force since 2017, set its size limit in LAMC 12.08 C.5: outside a Hillside Area or the Coastal Zone, "the maximum Residential Floor Area contained in all buildings and accessory buildings shall not exceed 45 percent of the lot area (a Residential Floor Area ratio of 0.45)." Residential floor area is the floor area inside the exterior walls, with some parking and small accessory buildings left out. A 5,000 square foot R1 lot therefore allows 2,250 square feet of residential floor area, by VanPlex arithmetic. The parking, setbacks and height page explains what counts.

The same ordinance created R1 variation zones that City Council can apply to a neighborhood. R1V is variable-mass, R1F front-mass, R1R rear-mass and R1H hillside. Each comes in four numbered versions with its own floor area ratio by lot size and its own lot coverage cap. Lot coverage is the share of the lot covered by structures more than six feet above grade.

Lot size R1V1, R1F1, R1R1 R1V2, R1F2, R1R2 R1V3, R1F3, R1R3 R1V4, R1F4, R1R4 Max lot coverage
Up to 6,000 sq ft 0.65 0.55 0.45 0.40 50%
6,001 to 7,000 sq ft 0.63 0.53 0.43 0.38 48%
7,001 to 8,000 sq ft 0.61 0.51 0.41 0.36 46%
8,001 to 9,000 sq ft 0.59 0.49 0.39 0.34 44%
9,001 to 10,000 sq ft 0.57 0.47 0.37 0.32 42%
Over 10,000 sq ft 0.55 0.45 0.35 0.30 40%

Residential floor area ratio by lot size. Source: Ordinance No. 184,802, Tables 12.08 C.5(b), (c) and (d), and the City Planning summary, pages 12 to 14.

The variation zones also set heights. In the summary, R1V1 and R1V2 allow a 30-foot building and R1V4 a 20-foot building. R1H zones use slope bands instead of lot size; the hillside and fire zones page covers them. A lot in a variation zone shows the full name, such as R1V2, in ZIMAS.

Two-Family and Multiple Dwelling Zones

Above R1, the zones count homes by lot area. The lot area per home column gives the lot area the zone needs for each dwelling unit. Divide the lot area by it to get the base count. The summary's note 13 gives the R3 example: one home per 800 square feet "is equivalent to 0.00125 Dwelling Units per Square Foot or 54.45 Dwelling Units per acre."

Zone Homes allowed Minimum lot Lot area per home Minimum width
R2 Two-family dwellings 5,000 sq ft Two homes per lot 50 ft
RD1.5 Apartment houses and multiple dwellings 5,000 sq ft 1,500 sq ft 50 ft
RD2 Same as RD1.5 5,000 sq ft 2,000 sq ft 50 ft
RD3 Same as RD1.5 6,000 sq ft 3,000 sq ft 60 ft
RD4 Same as RD1.5 8,000 sq ft 4,000 sq ft 60 ft
RD5 Same as RD1.5 10,000 sq ft 5,000 sq ft 70 ft
RD6 Same as RD1.5 12,000 sq ft 6,000 sq ft 70 ft
R3 R2 uses, apartment houses, multiple dwellings 5,000 sq ft 800 sq ft 50 ft
R4 R3 uses and more See the zone 400 sq ft See the zone
R5 R4 uses and more See the zone 200 sq ft See the zone

Source: LA City Planning, Generalized Summary of Zoning Regulations, Tables 1a and 1b. In the summary, RD1.5 and RD2 share one lot area and width cell, as do RD3 and RD4 (width) and RD5 and RD6 (width).

By VanPlex arithmetic, a 6,000 square foot lot holds four homes in RD1.5, three in RD2 and two in RD3. A 5,600 square foot R3 lot holds seven. The RD and R3 zones are where Los Angeles allows fourplexes and small apartment buildings by zone alone. The R2 zone allows two homes, and the summary says the RD zones allow "One-Family Dwellings, Two-Family Dwellings, Apartment Houses, Multiple Dwellings."

These zones matter for state law too. City Planning lists R2, RD, RW2, R3, RAS3, R4, RAS4, R5 and all C zones as the multifamily zones where the Starter Home Revitalization Act (SB 684 and SB 1123) can split a lot into up to 10 small lots. The lot size and subdivisions page explains that process, and the three or more homes page covers the bonus programs that add homes above the zone count.

Density Districts in Chapter 1A

Chapter 1A writes a zone as a string of five districts in two sets of brackets: [Form - Frontage - Standards] [Use - Density]. The density district sets the number of homes. Division 6B.1 says that in "1L, 2L, 3L and 4L Density Districts, the maximum number of dwelling units permitted on a lot is limited" to 1, 2, 3 or 4. Division 6B.2 sets lot-area districts by number: in density district 2 each home needs 200 square feet of lot area, in district 3, 300 square feet, and in district 4, 400 square feet.

City Planning treats the 1L density district as a single-family zone for SB 9. A Downtown lot with a different density district follows that district's count, and the bonus programs in Article 9 of Chapter 1A can add homes above it.

Historic Districts and Other Overlays

City Planning's local historic districts page lists 36 districts, including North University Park, a Specific Plan area that uses HPOZ rules. The page says "All exterior work proposed in an HPOZ, including landscaping, alterations, additions, and new construction, is subject to additional review," and that each district has a Preservation Plan and an HPOZ Board. In an HPOZ, SB 9 applies only in limited cases; the ADUs and SB 9 page gives them.

Zoning plan check is the review of a building permit for zoning rules. The summary's January 2026 update notes "Zoning Review's transfer from the Department of Building and Safety (LADBS) to the Department of City Planning (DCP)." City Planning's Zoning Review page says permit applications that need it "are automatically routed to City Planning's Zoning Review Division via ePlanLA," and offers a Preliminary Zoning Assessment, an early zoning check that "is a City Planning application requirement for most housing projects."

Best For

  • ✓ An RD1.5 or RD2 lot, where the zone alone allows a fourplex on 6,000 or 8,000 sq ft.
  • ✓ An R1, RS or RE lot that qualifies for SB 9 and ADUs, which add homes above the one-house zone.
  • ✓ An R2 or RD lot in a multifamily zone that can use the SHRA small-lot map.

Usually Fails When

  • ✕ A Q condition or D limitation on the lot is stricter than the zone and was not read.
  • ✕ The lot is in an HPOZ and the plan alters a contributing structure.
  • ✕ The lot is in an R1 variation zone and the design used the plain R1 floor area of 0.45.

What To Verify Before Spending Money

  • → The full zone string, height district and any Q, D or T in ZIMAS.
  • → Whether the lot is in a Specific Plan, CPIO, HPOZ or the Chapter 1A Downtown area.
  • → The SB 9 and SHRA eligibility checklists linked in ZIMAS.

Where to Go Next

Related on VanPlex: the Los Angeles overview, SB 9 in California and is your lot eligible.

Frequently Asked Questions

How do I find the zone of my lot in Los Angeles? +
Search the address in ZIMAS, the City of Los Angeles zoning map, and open its Planning and Zoning tab. A zone such as R1-1 names the zone class first and the height district second. The same tab links the SB 9, SHRA and AB 2097 eligibility checklists. A lot under the new Chapter 1A code carries a zone string of five districts in brackets.
How many homes can I build on an R1 lot in Los Angeles? +
An R1 lot in Los Angeles is a one-family zone that requires 5,000 square feet and 50 feet of width. The zone itself allows one main house. State law adds more: SB 9 allows two primary homes or a lot split, and ADU law adds accessory units. In Opportunity Station Areas near transit, the Low-Rise Ordinance of June 2026 allows 5 to 16 homes with affordable units.
What is the difference between R1 and RS zoning in Los Angeles? +
Both are one-family zones in Los Angeles. The City Planning summary lists a minimum lot of 5,000 square feet and 50 feet of width for R1, and 7,500 square feet and 60 feet for RS. The R1 rear yard is 15 feet and the RS rear yard is 20 feet. Both zones count as single-family zones for SB 9.
Can I build a duplex in the R2 zone in Los Angeles? +
Yes. The City Planning summary lists two-family dwellings as the use of the Los Angeles R2 zone, on a minimum lot of 5,000 square feet and 50 feet of width. A note in the same summary says a maximum of two dwelling units are allowed per lot based on lot area rules. R2 is not a single-family zone, so SB 9 does not apply there.
How many units can I build in an RD1.5 zone in Los Angeles? +
The Los Angeles RD1.5 zone allows one home for each 1,500 square feet of lot area, on a lot of at least 5,000 square feet. A 6,000 square foot RD1.5 lot therefore holds four homes under the zone, by VanPlex arithmetic. The State Density Bonus Program and the Low-Rise Incentive Area can add more homes in exchange for affordable units.
What is the new Chapter 1A zoning code in Los Angeles? +
Chapter 1A is the new Los Angeles zoning code, which City Planning says was adopted in October 2024; its book cites Ordinance No. 188,418, effective January 20, 2025. It writes each zone as a string of five districts for form, frontage, standards, use and density. It applies in the Downtown Community Plan Area, and the existing code continues elsewhere.
What are the R1V, R1F, R1R and R1H zones in Los Angeles? +
They are variations of the Los Angeles R1 zone created by Ordinance No. 184,802 in 2017. R1V allows flexibility in where the house mass sits, R1F and R1R set separate height limits for a front mass and a rear mass, and R1H applies the hillside rules. Their floor area ratios run from 0.65 to 0.30 by zone and lot size.
What does a Q or D in a Los Angeles zone mean? +
In Los Angeles, a Q before the zone is a qualified classification that restricts the uses allowed on the property, and a D after the height district is a development limitation on height, floor area, lot coverage or setbacks. A T marks a tentative classification that waits on dedications or improvements. Each one is set by ordinance for that lot.
Which Los Angeles zones count as single-family zones for SB 9? +
Los Angeles City Planning lists the A, RA, RE, RS, R1, RU, RZ and RW1 zones of Chapter 1, and the 1L density district of Chapter 1A, as the single-family zones where SB 9 applies. R2, RD and R3 lots are outside that list. The SB 9 checklist in ZIMAS shows whether a specific lot passes the other site tests.
How many historic districts does Los Angeles have? +
The Los Angeles City Planning page on local historic districts lists 36 districts, called Historic Preservation Overlay Zones or HPOZs. One of them, North University Park, is a Specific Plan area that uses HPOZ rules. In an HPOZ all exterior work, including additions and new construction, gets added review under the district Preservation Plan.

Official sources (checked October 2026)

VanPlex newsletter

Get new guides by email

New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.

General information, not legal advice. California housing law changes every year, and each city adds its own rules on top of state law. Confirm current requirements with the city or county planning department, and with a California-licensed attorney or architect, before you buy land or file plans.

Planning a multiplex in Los Angeles?

VanPlex builds multiplexes in British Columbia, Canada. For a lot in Los Angeles, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.

Get a proforma for your address