David Babakaiff
Written by David Babakaiff · Co-Founder, VanPlex | 25+ Years BC Construction Last reviewed: October 2026

Los Angeles | Parking, Setbacks, Height

Los Angeles Parking, Setbacks and Height: R1 Floor Area, Yards and Parking by Zone

The zone sets how many homes a Los Angeles lot may hold; the rules on this page set how big they can be and where they sit. Most single-family lots follow the 2017 amendments to the Baseline Mansionization Ordinance, Ordinance No. 184,802, which set floor area, an angled height limit and side wall rules. The figures for other zones come from the City Planning summary. Hillside lots follow different rules, on the hillside and fire zones page.

Size, yards and parking in six facts

Floor Area in the R1 Zone

Ordinance No. 184,802 opens by explaining its purpose: the 2008 Baseline Mansionization Ordinance had set "height and floor area ratio (FAR) limitations" for single-family lots outside the Hillside Area and Coastal Zone, but "out-of-scale development continues to occur." Its amendment to LAMC 12.08 C.5(a) sets the R1 limit: "the maximum Residential Floor Area contained in all buildings and accessory buildings shall not exceed 45 percent of the lot area (a Residential Floor Area ratio of 0.45)." A 6,000 square foot R1 lot therefore allows 2,700 square feet, by VanPlex arithmetic.

Residential floor area is "The area in square feet confined within the exterior walls" of a building on an RA, RE, RS or R1 lot. Two rules make it larger than the rooms suggest. "Any floor or portion of a floor with a ceiling height greater than 14 feet shall count as twice the square footage of that area," and an attic with a ceiling over 7 feet counts. Four things are left out:

  • Required covered parking: 200 square feet per required covered space, up to 400, when all of it is in the rear half of the lot or at least 55 feet from the front lot line; otherwise only 200 square feet.
  • Small accessory buildings: detached accessory buildings of up to 200 square feet each, with no more than 400 square feet left out in total.
  • Lattice roof porches, patios and breezeways.
  • Basements: outside the Hillside Area and Coastal Zone, a basement whose top is no more than 2 feet above grade at any point.

The limit covers all buildings on the lot, so a garage or studio counts against it unless an exemption applies. State law sets floors under it: an SB 9 home gets at least 800 square feet, and the City's SB 9 memo says residential floor area "applies in the RA, RE, RS, RU, RZ, RW1, and R1 Zones." ZA Memo 143 says residential floor area "may not be enforced on State ADUs." The R1 variation zones have their own ratios, from 0.65 to 0.30, listed on the zoning districts page.

For small additions, the City uses the County's records. Under LAMC 12.08 C.6, for additions under 1,000 square feet or remodels of homes built before January 1, 2008, existing floor area is "determined based on the building records or the building square footage shown on the most recent Los Angeles County Tax Assessor's records," unless an architect or engineer submits a full set of measured plans. A remodel keeps at least 50 percent of the outside walls and 50 percent of the roof; work that keeps less does not count as a remodel and needs a full set of measured plans.

The Encroachment Plane and Side Wall Rule

Ordinance No. 184,802 defines the encroachment plane as "An invisible inclined plane sloping inward at a forty-five degree angle" from a set height above the front and side yard lines. In R1, "The encroachment plane shall originate from a point that is 20 feet in height from the existing or finished grade, whichever is lower, along the required front and side yard setbacks." The house must fit under it. The City Planning summary adds that the mass may not extend above the plane "except for specified roof structures and equipment." The upper part of a wall near a side yard therefore has to step back or slope away from the lot line.

The side wall rule limits long flat walls. "All portions of a building that have a side wall exceeding 14 feet in height and a continuous length greater than 45 feet shall have an offset/plane break that is a minimum depth of five feet beyond the required yard and a minimum length of 10 feet." An offset is a section of wall set back farther from the lot line. Any occupied rooftop deck must sit at least three feet back from the side yard, except on the street side of a corner lot.

Yards by Zone

A yard, or setback, is the open space required between a building and a lot line. "Prevailing" in the table refers to the prevailing setback. The LADBS Zoning Code Manual shows it worked out as an average of the front yards of developed lots on the same frontage, the stretch of one side of a street between cross streets, and calls it "a generic term that applies to the entire block."

Zone Front Side Rear
R1 20% of lot depth, 20 ft max, not less than prevailing 5 ft; 10% of lot width on lots under 50 ft wide, at least 3 ft 15 ft
RS 20% of lot depth, 25 ft max, not less than prevailing 5 ft; 10% of lot width on lots under 50 ft wide, at least 3 ft 20 ft
R2 20% of lot depth, 20 ft max, not less than prevailing 5 ft; 10% of lot width on lots under 50 ft wide; 3 ft min 15 ft
RD1.5, RD2 15 ft 5 ft, or 10% of width under 50 ft; 3 ft min; plus 1 ft per story over the 2nd, up to 16 ft 15 ft
RD3, RD4 15 ft 10% of lot width, 10 ft max, 5 ft min 15 ft
RD5, RD6 20 ft 10 ft 25 ft
R3 15 ft; 10 ft for key lots 5 ft; 10% of width under 50 ft; 3 ft min; plus 1 ft per story over the 2nd, up to 16 ft 15 ft

Source: LA City Planning, Generalized Summary of Zoning Regulations, Tables 1a and 1b (CP-7150, 1.20.2026). Hillside Area lots follow Table 12.21 C.10-1 instead.

Height adds to the side yard. Under LAMC 12.08 C.2(a), for an R1 building over two stories, "1 foot shall be added to the width of each yard for each additional story above the second story." For new construction or a ground floor addition outside a Hillside Area or Coastal Zone, 12.08 C.2(b) uses height instead: "one-foot shall be added to each required side yard for each increment of ten feet or fraction thereof above the first 18 feet." A home 28 feet tall therefore needs a 6-foot side yard on a 50-foot lot, by VanPlex arithmetic. In the Coastal Zone outside the Hillside Area, the summary says one foot is added "for each additional story above the second story."

Side yard rules in a Specific Plan, an HPOZ or a subdivision approval "shall take precedence" over 12.08 C.2. State programs also replace yards: SB 9 and ADUs cap side and rear setbacks at four feet, and the Low-Rise Ordinance sets three- or four-foot side yards and an eight-foot rear yard, as the three or more homes page explains. The City Planning Zoning Review page offers a yard setback calculator.

Height by Zone and Height District

Height in Los Angeles depends on both the zone and the height district, the number after the zone name, such as the 1 in R1-1. For single-family zones the limit also depends on the roof: the summary gives one figure for a roof sloped at 25 percent or more and a lower one for a flatter roof.

Zone Height District 1 Height District 1XL Height District 1SS
R1, RS, RE9 33 ft (roof 25% or steeper), 28 ft (flatter) 30 ft or 28 ft 18 ft (22 ft in a Hillside Area for steep roofs)
RE11, RE15, RE20, RE40, RA 36 ft (roof 25% or steeper), 30 ft (flatter) 30 ft 18 ft (22 ft in a Hillside Area for steep roofs)
R2 33 ft 30 ft, 2 stories Not listed
RD, R3 45 ft 30 ft, 2 stories Not listed

Source: LA City Planning, Generalized Summary, Table 2. For the single-family zones the same figures apply in Height Districts 1L and 1VL. For R2, RD and R3, 1VL allows the same feet with a 3-story limit; Height Districts 2 to 4 allow 75 feet for RD and R3.

Three notes in the summary change these figures. On lots in the Coastal Zone outside the Hillside Area, single-family height is "limited to 45 feet," and those lots follow floor area ratio limits instead of residential floor area. R1 variation zones follow their own height tables, such as 30 feet in R1V1 and 20 feet in R1V4. "Buildings used entirely for residential" use are limited only in feet, not stories, in the multifamily zones where the table lists stories.

Parking

Los Angeles sets parking minimums by zone, and state laws cut them for many small projects. The table lists both.

Home or project Parking required
R1, RS, RE or RA home 2 covered spaces per home
R2 home 2 spaces, one covered
RD or R3 home with fewer than 3 habitable rooms 1 space
RD or R3 home with 3 habitable rooms 1.5 spaces
RD or R3 home with more than 3 habitable rooms 2 spaces
SB 9 home Up to 1 covered space, or none near qualifying transit or car share
ADU 1 space, or none under a state or City exemption
Junior ADU None
Low-Rise Incentive Area project None
Project within a half mile of a major transit stop (AB 2097) No minimum, with limited exceptions

Sources: Generalized Summary, Tables 1a and 1b; SB 9 memo; ZA Memo 143; Ordinance No. 188,967; AB 2097 page.

AB 2097 is a state parking law. City Planning's AB 2097 page says it "prohibits public agencies or cities from imposing a minimum automobile parking requirement on most development projects located within a half-mile radius of a major transit stop." Public Resources Code 21064.3 defines a major transit stop. The City may still require parking if it makes one of three findings within 30 days, but not for projects that set aside 20 percent of homes as affordable, projects with "fewer than 20 dwelling units," or projects that qualify for another parking reduction. ZIMAS shows an "AB 2097 Eligibility" field for each lot.

When parking is required on a single-family lot, garage and driveway rules follow. The SB 9 memo says the requirement "for a private garage in most single-family zones (Los Angeles Municipal Code [LAMC] Section 12.21 A.4(a))" applies. Driveways must be at least 9 feet wide in the A, RE, RS, R1, RU, RZ, R2, RMP and RW zones and 10 feet in RD and R3. In R1 outside a Hillside Area, "driveway width at the front property line shall not exceed 25 percent of the lot width or the width of any currently existing driveway, whichever is greater."

Larger projects add other spaces. The summary says open space is "Required for 6 or more residential units in accordance with Section 12.21 G," a 10-foot passageway is required "from the street to one entrance of each dwelling unit" except in the RW, RU and RZ zones, and bicycle parking follows LAMC 12.21 A.16. ADUs and Low-Rise projects are exempt from the passageway rule, and the SB 9 memo says spacing rules may not be used to deny an SB 9 project for proposing adjacent buildings.

Best For

  • ✓ An R1 lot outside the Hillside Area where 45 percent of the lot area covers the planned homes and garage.
  • ✓ A design with a pitched roof of 25 percent or steeper, which earns 33 feet in place of 28 in Height District 1.
  • ✓ A lot within a half mile of a major transit stop, where AB 2097 removes parking minimums.

Usually Fails When

  • ✕ The plan has a long two-story side wall with no 5-foot offset.
  • ✕ A double-height room or tall attic was left out of the floor area count.
  • ✕ The garage sits at the front and the plan assumed 400 sq ft of parking exemption.

What To Verify Before Spending Money

  • → The height district (the number after the zone) and any R1 variation zone in ZIMAS.
  • → The prevailing front setback on the block.
  • → AB 2097 eligibility for the lot, shown in ZIMAS.

Where to Go Next

Related on VanPlex: the Los Angeles overview, duplex to fourplex in California and the California Energy Code.

Frequently Asked Questions

How big a house can I build on an R1 lot in Los Angeles? +
Outside the Hillside Area and Coastal Zone, LAMC 12.08 C.5(a) caps residential floor area on a Los Angeles R1 lot at 45 percent of the lot area, counting all buildings. On a 5,000 square foot lot that is 2,250 square feet, by VanPlex arithmetic. Up to 400 square feet of required covered parking can be left out when placed toward the rear.
What is the encroachment plane in Los Angeles? +
The Los Angeles encroachment plane is an imaginary surface that starts at a set height above the required front and side yard lines and slopes inward at 45 degrees. In the R1 zone it starts 20 feet above grade, under Ordinance No. 184,802. The building may not extend above that plane, except for listed roof structures and equipment.
How tall can a house be in the R1 zone in Los Angeles? +
In Height District 1, an R1 home in Los Angeles may be 33 feet tall when the roof slope is 25 percent or more, and 28 feet with a flatter roof, under the City Planning zoning summary. The 1XL district allows 30 or 28 feet, and the single-story 1SS district 18 feet. The encroachment plane also applies.
What side yard does an R1 lot need in Los Angeles? +
Under LAMC 12.08 C.2, a Los Angeles R1 home of up to two stories needs side yards of 5 feet, or 10 percent of the lot width on lots under 50 feet wide but never under 3 feet. For new construction outside hillside and coastal areas, one foot is added for each 10 feet of height above the first 18 feet.
Does a garage count as floor area in Los Angeles? +
Partly. Los Angeles counts residential floor area inside exterior walls, but leaves out 200 square feet for each required covered parking space, up to 400 square feet, when all of it sits in the rear half of the lot or at least 55 feet from the front lot line. Otherwise only 200 square feet is left out, under Ordinance No. 184,802.
How many parking spaces does a duplex need in Los Angeles? +
A duplex in the Los Angeles R2 zone needs two spaces per home, one of them covered, under the City Planning zoning summary. An SB 9 duplex in a single-family zone needs at most one covered space per home, and none within a half mile walk of qualifying transit. AB 2097 removes minimums near major transit stops.
Can Los Angeles require parking near a major transit stop? +
Only in limited cases. Los Angeles City Planning says AB 2097 bars minimum car parking within a half mile of a major transit stop. The City may impose parking only with findings that the project would have a "substantially negative impact," and never on projects with fewer than 20 homes, projects with 20 percent of homes affordable, or projects that qualify for another parking reduction.
How wide can a driveway be on an R1 lot in Los Angeles? +
Outside a Hillside Area, a Los Angeles R1 driveway at the front property line may not exceed 25 percent of the lot width or the width of an existing driveway, whichever is greater, under LAMC 12.21 A.5(f) as amended by Ordinance No. 184,802. No driveway has to be narrower than 9 feet, the minimum for R1.
What setbacks apply in the RD1.5 zone in Los Angeles? +
The City Planning summary lists, for the Los Angeles RD1.5 and RD2 zones, a 15-foot front yard and a 15-foot rear yard. Side yards are 5 feet, or 10 percent of lot width on lots under 50 feet wide but at least 3 feet, plus one foot for each story above the second, up to 16 feet.
Do apartment projects need open space in Los Angeles? +
Yes, once a project has six or more homes. The Los Angeles City Planning zoning summary says open space is "Required for 6 or more residential units" under LAMC 12.21 G. It also lists a 10-foot passageway from the street to an entrance of each home, except in the RW, RU and RZ zones, under LAMC 12.21 C.2.

Official sources (checked October 2026)

VanPlex newsletter

Get new guides by email

New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.

General information, not legal advice. California housing law changes every year, and each city adds its own rules on top of state law. Confirm current requirements with the city or county planning department, and with a California-licensed attorney or architect, before you buy land or file plans.

Planning a multiplex in Los Angeles?

VanPlex builds multiplexes in British Columbia, Canada. For a lot in Los Angeles, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.

Get a proforma for your address