David Babakaiff
Written by David Babakaiff · Co-Founder, VanPlex | 25+ Years BC Construction Last reviewed: October 2026

Austin | Lot Size and Small Lots

Austin Lot Size, Lot Width and Small Lots Under HOME Phase 2

Two lot sizes matter for a small project in Austin. A lot of 5,750 square feet is the standard in the SF-2 and SF-3 districts and is the size that two or three homes need. A lot of 1,800 square feet is the smallest that may hold one home under the City's second HOME ordinance. This page gives the lot area and width rules of the Land Development Code (LDC), the ways to create a small lot, the rules for flag lots and older lots, and how the state law SB 15 fits in. The Austin overview gives the short version.

Austin lot size in six facts

The Standard Lot in Each District

The table in Section 25-2-492 sets a minimum lot size and a minimum lot width for each zoning district. Section 25-4-174 makes the same table the rule for new plats: inside the City's zoning jurisdiction, the zoning district of a lot decides its minimum area and width. A plat is the recorded map that creates lots.

District Minimum lot size Minimum lot width
LA and RR 43,560 sq ft 100 feet
SF-1 10,000 sq ft 60 feet
SF-2 and SF-3 5,750 sq ft 50 feet
SF-5 and SF-6 5,750 sq ft 50 feet
MF-1 to MF-6 8,000 sq ft 50 feet

Source: Austin LDC 25-2-492(D), rows "MINIMUM LOT SIZE (square feet)" and "MINIMUM LOT WIDTH," Supplement 174. For SF-4A and SF-4B the table refers to other sections.

Section 25-1-22 says how the numbers are measured. Lot area is the net horizontal area inside the lot lines. Lot width "is measured at the front setback line and at a distance of 20 feet to the rear of the front setback line," so a lot that narrows toward the back can fail the width test. The setback line is the line a building must stay behind. Section 25-2-512 then protects the minimum: "a lot may not be reduced in area, width, or depth to less than the minimum requirements," apart from two cases such as land taken for public use.

The 5,750 figure also decides how many homes a lot may hold. Section 25-2-773 sets a minimum lot area of 5,750 square feet for a duplex, a two-unit use or a three-unit use. In SF-1 the base minimum is 10,000 square feet, and the section says it supersedes the base district rules where the two conflict. The duplexes and second units page covers that use.

HOME Phase 2: One Home on 1,800 Square Feet

The Council adopted Ordinance No. 20240516-006, called HOME Phase 2, on May 16, 2024. It rewrote Section 25-2-779, the rules for "small lot single-family residential use." The code defines a small lot as a lot with an area of less than 5,750 square feet. The use table permits this use in SF-1, SF-2, SF-3, SF-4A, SF-4B, SF-5 and SF-6.

The section now holds two sets of rules. Subsection (D) keeps the older rules for land zoned SF-4A or less restrictive. Subsections (F) through (L) are the Phase 2 rules for land zoned SF-3 or more restrictive, which means SF-3, SF-2 and SF-1 for this use. Their first line is: "A lot must be at least 1,800 square feet but less than 5,750 square feet." One line applies to both sets: "Only one dwelling unit is permitted on a lot."

Rule Small lot in SF-1, SF-2 or SF-3 (Phase 2) Small lot in SF-4A
Lot area At least 1,800 sq ft and less than 5,750 sq ft At least 3,600 sq ft, or 4,500 sq ft for a corner lot
Lot width 15 feet, or 20 feet for a flag lot apart from its access strip 40 feet for an interior lot and 50 feet for a corner lot
Homes per lot One One
Front yard setback 10 feet, or 5 feet on a flag lot 15 feet
Street side yard setback Level 1 street: the greater of 5 feet from the property line or 10 feet from the curb. Level 2, 3 or 4 street: 10 feet 10 feet
Side yard setback 5 feet, or zero next to a flag lot access strip or a lot subdivided to less than 5,750 sq ft and approved on or after August 16, 2024 3.5 feet, and 7 feet for the two side yards together
Rear yard setback 5 feet, or zero on a line shared with a lot subdivided to less than 5,750 sq ft on or after August 16, 2024 5 feet, excluding easements
Building coverage No limit 55 percent
Impervious cover The maximum of the base district 65 percent
Floor area inside the Subchapter F area The greater of 1,650 sq ft or a 0.55 floor-to-area ratio, and no home over 2,300 sq ft No figure in Section 25-2-779(D)

Sources: Austin LDC 25-2-779(C) to (J) and 25-4-232(C), Supplement 174. The code sorts streets into Level 1 to Level 4; ask the City for the level of your street.

Three terms in the table need a plain meaning. Building coverage is the share of the lot under buildings and roofs. Impervious cover is the share under any surface that stops water from soaking into the ground, such as roofs, driveways and concrete. The floor-to-area ratio is the floor area of the buildings divided by the area of the lot. Phase 2 removes the building coverage limit and keeps the impervious cover limit of the base district, which the table in Section 25-2-492 sets at 45 percent in SF-2 and SF-3 and 40 percent in SF-1. On a 1,800 square foot lot in SF-3, 45 percent is 810 square feet of roof and paving together.

The floor area limit applies inside the area described in Subchapter F of the zoning chapter, the City's residential design rules for its central neighborhoods. There the gross floor area of a small lot home may not exceed the greater of 1,650 square feet or a ratio of 0.55. The section adds: "The maximum unit size is 2,300 square feet." The rest of Subchapter F does not apply to a Phase 2 small lot. The parking, setbacks and height page describes that subchapter.

Phase 2 took effect on May 27, 2024. Part 10 of the ordinance phased it in: it applies to an application filed on or after August 16, 2024, and on or after November 16, 2024 for a property in the wildland-urban interface area or in a census tract that the Uprooted Report identifies as vulnerable to displacement or undergoing it. The wildland-urban interface is the land where homes meet vegetation that can burn.

Entrances, Garages and Driveways on a Small Lot

Subsection (K) sets design rules for Phase 2 small lots that are not flag lots. The home needs at least one entrance that faces the street. A garage or carport may not sit closer to the front lot line than the front wall of the first floor. If a garage that faces the street is less than 5 feet behind that wall, it may not be wider than the wall.

Subsection (L) decides where a car may enter, by the width of the lot:

  • Less than 20 feet wide. Vehicle access only from an improved alley or from a side street.
  • 20 feet or more and less than 30 feet. Access from an improved alley, a side street, or a joint-use driveway with adjoining lots. A joint-use driveway is one driveway that serves two or more lots.
  • 30 feet or more. Access from an improved alley, a joint-use driveway, or the lot's own driveway.

The front yard has its own cap. Except on a flag lot, driveways and parking areas may cover at most 50 percent of the front yard. Austin requires no car parking for a home, so a small lot may be built with none. The parking page linked above explains that rule.

How a Small Lot Is Created

The City's HOME amendments page lists three kinds of application under Phase 2:

  • A subdivision application. "Unless an existing lot is already below 5,750 square feet, a subdivision application is required" to divide the lot into smaller ones.
  • A residential infill application. The City describes this as a new subdivision process for smaller cases. The site must not exceed one acre, must be a resubdivision or replat, must include only land that was platted as a residential subdivision, and must not require a plat vacation, which is the cancelling of the old plat.
  • A building permit application. For an existing lot that is already below 5,750 square feet, the permit application is what sets up the small lot single-family use.

The arithmetic of a split is short. Take a lot 50 feet wide and 120 feet deep, which is 6,000 square feet. Divided side by side into three lots, each is 16.67 feet wide and 2,000 square feet. Each one passes the 15-foot and 1,800 square foot tests. Each is also under 20 feet wide, so under Subsection (L) cars may reach it only from an improved alley or a side street. Divided into two lots of 25 feet, each lot may use a joint-use driveway.

Drainage review is lighter for the smallest splits. Under Section 25-7-67, a residential infill project that is a resubdivision of no more than 17,780 square feet of gross site area is released from three of the code's drainage sections. The plats, permits and fees page covers the plat steps and the City's fees, and the watersheds page covers drainage.

Flag Lots

A flag lot is "a lot that abuts a street by means of a strip of land that does not comply with the requirements of this chapter for minimum lot width." The strip is the pole and the buildable part behind another lot is the flag. Flag lots let a deep lot be split front and back.

Section 25-4-177 governs them. In a subdivision of previously unplatted land for single-family, duplex, two-unit or three-unit use, flag lots may be used where no more than two dwelling units share a driveway. More homes on one driveway are allowed if the lots meet the Fire Code, the utility design criteria, the Plumbing Code and the access requirements. The section sets the minimum width of a flag lot at 20 feet, or 15 feet in three listed cases, such as two or more contiguous lots that share a common driveway. For a flag lot with one to three dwelling units it sets 10 feet when there is room for utilities and no driveway is proposed, and 5 feet when two or more contiguous lots share a common driveway or walkway or the applicant shows access by another route. Every flag lot address must be displayed at its closest point of access to a public street, for emergency responders.

Three other rules follow a flag lot. Section 25-1-22 leaves the access strip out of the lot area, so the 1,800 square feet must lie in the flag itself. Section 25-2-779 requires the flag to be at least 20 feet wide. And the Phase 2 front setback on a flag lot is 5 feet, or zero where the front line is shared with a small lot created on or after August 16, 2024.

Older Lots, SF-4A Lots and Attached Homes

  • Substandard lots. A substandard lot is one that met the rules when it was recorded and is smaller than the current minimum. Under Section 25-2-943, one recorded before March 15, 1946 may hold a single-family home if it has at least 4,000 square feet and is at least 33 feet wide. One recorded after March 14, 1946 needs 5,750 square feet and 50 feet. A substandard lot that was combined with other land to form a site may not be separated again after August 6, 2007 to form a site below the minimum.
  • Neighborhood plan lots. In a neighborhood plan combining district, the ordinance may allow a single-family home on an existing legal lot of 2,500 square feet and 25 feet of width under Section 25-2-1406. The City's HOME page says: "Small Lot Amnesty cannot be combined with Small Lot Single Family Residential Use."
  • SF-4A subdivisions. Section 25-4-232 requires public water and central sewer for every lot, underground utilities, and a recorded Declaration of Covenants, Easements, and Restrictions approved by the city attorney. A lot may have one zero lot line, which means the house wall may sit on one side line.
  • Single-family attached lots. Under Section 25-2-772, two attached homes may each sit on a lot of 3,000 square feet and 25 feet of width, on a site of at least 7,000 square feet. The use is prohibited on property subject to a deed restriction that limits it to single-family detached dwellings.
  • Townhouse lots. Section 25-2-775 sets a minimum lot width of 20 feet and requires 3,600 square feet of site area for each townhouse.

How SB 15 Applies in Austin

SB 15 is the 2025 state law on small lots. It added a subchapter to Local Government Code chapter 211 that took effect on September 1, 2025. It covers a city of more than 150,000 people in a county of more than 300,000, and within that city only a tract that will be platted, is in an area zoned for single-family homes, is five acres or more and "has no recorded plat." On such a tract the city may not require a residential lot to be larger than 3,000 square feet, wider than 30 feet or deeper than 75 feet.

Austin's code, as published in Supplement 174, has no section that names SB 15. In SF-1, SF-2 and SF-3 the City's own small lot use already goes lower than the state figure: 1,800 square feet and 15 feet of width. In other single-family districts the printed minimums are larger than 3,000 square feet, for example 3,600 square feet in SF-4A and one acre in RR. For an unplatted tract of five acres or more in one of those districts, the state statute limits what the City may require, so ask the City how it applies SB 15 before you design the lots. Infill lots that are already platted are outside SB 15. The SB 15 page explains the state law in full.

One limit sits outside the code. Private deed restrictions can set a larger minimum lot or forbid a split, and the City's deed restrictions page says staff must approve a permit that meets the code whether or not it conforms to a deed restriction. The parties named in the restriction, such as a property owners' association, can still enforce it as a civil matter, so read the recorded restrictions first.

Best For

  • ✓ A lot in SF-1, SF-2 or SF-3 with an alley or a side street, where lots of 15 to 20 feet of width can take cars.
  • ✓ A deep lot that can be split front and back with a flag lot of at least 20 feet of width.
  • ✓ An existing lot already under 5,750 sq ft, which needs a building permit and no plat.

Usually Fails When

  • ✕ The plan puts two homes on one small lot, since a small lot may hold one dwelling unit.
  • ✕ A new lot is under 20 feet wide and has no improved alley or side street for cars.
  • ✕ Recorded deed restrictions set a larger minimum lot or forbid resubdivision.

What To Verify Before Spending Money

  • → The lot width at the front setback line and 20 feet behind it.
  • → Whether the land was platted as a residential subdivision, which the infill process requires.
  • → Whether the lot is inside the Subchapter F area, which brings the 1,650 sq ft or 0.55 limit.

Where to Go Next

Related on VanPlex: the Austin overview, the SB 15 small lots page, and how Texas zoning and deed restrictions work.

Frequently Asked Questions

What is the minimum lot size for a house in Austin? +
Austin's minimum lot size for a house depends on the zoning district. The table in Section 25-2-492 of the Land Development Code sets 5,750 square feet in SF-2 and SF-3, 10,000 square feet in SF-1 and 43,560 square feet, which is one acre, in LA and RR. Since 2024 a small lot single-family use may also sit on 1,800 square feet in SF-1, SF-2 and SF-3.
How wide does a lot have to be in Austin? +
A standard Austin lot must be 50 feet wide in SF-2 and SF-3, 60 feet in SF-1 and 100 feet in LA and RR, under Section 25-2-492. Section 25-1-22 measures lot width at the front setback line and again 20 feet behind that line. A small lot single-family lot under Section 25-2-779 may be as narrow as 15 feet.
Can I split my Austin lot into two or three lots? +
You can split an Austin lot zoned SF-1, SF-2 or SF-3 if each new lot has at least 1,800 square feet and 15 feet of width for a small lot single-family use. The City's HOME page says a subdivision application is required unless the lot is already below 5,750 square feet. Each new small lot may hold one home.
Can I build a duplex on a small lot in Austin? +
A duplex needs a full-size lot in Austin. Section 25-2-779(C) says only one dwelling unit is permitted on a lot used for small lot single-family residential use. Section 25-2-773 sets a minimum lot area of 5,750 square feet for a duplex, a two-unit use or a three-unit use. The City also states that the preservation bonus is unavailable to small lot single-family use.
What is a flag lot in Austin? +
Austin's code defines a flag lot as a lot that reaches a street by a strip of land narrower than the minimum lot width. Under Section 25-1-22 the strip is left out of the lot area. For a small lot single-family use, the rest of the flag lot must be at least 20 feet wide and the front setback is 5 feet.
Can I build on an old Austin lot that is smaller than 5,750 square feet? +
Yes, in two cases. Austin Section 25-2-943 lets a substandard lot recorded before March 15, 1946 hold a single-family home if it has at least 4,000 square feet and is at least 33 feet wide. Separately, the City says a building permit application is enough to set up a small lot single-family use on an existing lot that is already below 5,750 square feet.
Where can the driveway go on a narrow Austin lot? +
Section 25-2-779(L) ties the driveway to the lot width for an Austin small lot single-family use. A lot under 20 feet wide may take vehicle access only from an improved alley or a side street. A lot of 20 to under 30 feet may also use a joint-use driveway shared with adjoining lots. A lot of 30 feet or more may have its own driveway.
How big a house fits on an 1,800 square foot lot in Austin? +
On an Austin small lot inside the Subchapter F area, Section 25-2-779(J) limits gross floor area to the greater of 1,650 square feet or a floor-to-area ratio of 0.55, and no home may exceed 2,300 square feet. On an 1,800 square foot lot that gives 1,650 square feet. Building coverage has no limit, and impervious cover follows the base district.
Does Texas SB 15 change lot sizes in Austin? +
SB 15 applies in Austin to a narrow set of land: a tract of five acres or more with no recorded plat, in an area zoned for single-family homes, that will be platted. On such a tract a city may not require a lot larger than 3,000 square feet. Austin's small lot use already allows 1,800 square feet in SF-1, SF-2 and SF-3.
What is the smallest lot for an attached home or townhouse in Austin? +
Austin Section 25-2-772 sets a minimum lot area of 3,000 square feet for each home in a single-family attached use, on a site of at least 7,000 square feet with two attached homes. For townhouses, Section 25-2-775 sets a minimum lot width of 20 feet and requires at least 3,600 square feet of site area for each townhouse.

Official sources (checked October 2026)

Austin LDC 25-2-492, site development regulations
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_CUSDERE_ART2PRUSDERE_DIV1RETA_S25-2-492SIDERE
Austin LDC 25-2-779, small lot single-family residential use
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_CUSDERE_ART4ADRECEUS_SPARESPUS_S25-2-779SMLOSIMIREUS
Austin LDC 25-2-773, duplex, two-unit and three-unit residential uses
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_CUSDERE_ART4ADRECEUS_SPARESPUS_S25-2-773DUTITTHITREUS
Austin LDC 25-1-21, definitions
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-1GEREPR_ART2DEME_S25-1-21DE
Austin LDC 25-1-22, measurements
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-1GEREPR_ART2DEME_S25-1-22ME
Austin LDC 25-4-177, flag lots
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-4SU_ART3PLRE_DIV3LO_S25-4-177FLLO
Austin LDC 25-4-232, small lot subdivisions
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-4SU_ART3PLRE_DIV6SPSU_S25-4-232SMLOSU
Austin LDC 25-4-233, single-family attached residential subdivision
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-4SU_ART3PLRE_DIV6SPSU_S25-4-233SIMIATRESU
Austin LDC 25-2-772, single-family attached residential use
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_CUSDERE_ART4ADRECEUS_SPARESPUS_S25-2-772SIMIATREUS
Austin LDC 25-2-775, townhouses
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_CUSDERE_ART4ADRECEUS_SPARESPUS_S25-2-775TO
Austin LDC 25-2-943, substandard lot
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_CUSDERE_ART7NOUS_S25-2-943SULO
Austin LDC 25-2-1406, neighborhood plan combining district ordinance requirements
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_DNEPLCODI_ART1GEPR_S25-2-1406ORRE
Austin LDC 25-7-67, modified drainage standards for residential infill
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-7DR_ART3REAP_S25-7-67MODRSTREIN
City of Austin, Ordinance No. 20240516-006 (HOME Phase 2, PDF)
https://services.austintexas.gov/edims/document.cfm?id=430451
City of Austin, HOME amendments
https://www.austintexas.gov/development-services/home-amendments
City of Austin, deed restrictions and development
https://www.austintexas.gov/development-services/deed-restrictions-and-development
Local Government Code 211.051 to 211.058, added by SB 15 (2025)
https://statutes.capitol.texas.gov/Docs/LG/htm/LG.211.htm#211.052
SB 15 (2025), enrolled bill text
https://capitol.texas.gov/tlodocs/89R/billtext/html/SB00015F.htm
VanPlex newsletter

Get new guides by email

New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.

General information, not legal advice. Texas has no statewide zoning code. Each city writes its own rules, and deed restrictions recorded on a lot can forbid what the city allows. Confirm current requirements with the city planning department, read the deed restrictions for your lot, and talk to a Texas-licensed attorney or architect before you buy land or file plans.

Planning a multiplex in Austin?

VanPlex builds multiplexes in British Columbia, Canada. For a lot in Austin, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.

Get a proforma for your address