David Babakaiff
Written by David Babakaiff · Co-Founder, VanPlex | 25+ Years BC Construction Last reviewed: October 2026

Austin | Zoning Districts

Austin Zoning Districts and How Many Homes Each Allows on a Lot

Zoning is the City's map of which uses and building sizes each piece of land may have. Austin's rules are in Chapter 25-2 of the Land Development Code (LDC), which is Title 25 of the City Code. The code names 16 residential base districts. Three of them, SF-1, SF-2 and SF-3, allow up to three homes on one lot. This page lists every residential district, the housing uses each one permits, the extra districts that can sit on top, and how a rezoning is decided. The Austin overview gives the short version.

Austin zoning in six facts

Base Districts and Map Codes

Section 25-2-221 requires all land in the City's zoning jurisdiction to carry a named base district. A base district is the main zone of a lot. The section adds that "only one zoning base district designation may apply to any portion of a site." Section 25-2-32 gives each district a short map code, and the code allows a district to be called by that code. So SF-3 on the zoning map means the family residence district.

Section 25-2-33 places the residential, commercial and industrial districts in one order. It "begins with the LA base district as the most restrictive district and ends with the LI base district as the least restrictive district." LI is limited industrial services. The order matters in other sections, which describe the lots a rule covers as zoned a named district "or more restrictive."

Code District name Minimum lot Homes allowed
LA Lake Austin residence 43,560 sq ft (one acre) One home per lot
RR Rural residence 43,560 sq ft (one acre) One home per lot
SF-1 Single-family residence large lot 10,000 sq ft Up to 3 homes per lot
SF-2 Single-family residence standard lot 5,750 sq ft Up to 3 homes per lot
SF-3 Family residence 5,750 sq ft Up to 3 homes per lot
SF-4A Single-family residence small lot 3,600 sq ft, or 4,500 sq ft on a corner One home per lot
SF-4B Single-family residence condominium site A site of 1 to 5 acres One home for each 3,600 sq ft of site
SF-5 Urban family residence 5,750 sq ft House, duplex, two-unit, townhouse or condominium
SF-6 Townhouse and condominium residence 5,750 sq ft House, duplex, two-unit, townhouse or condominium
MF-1 Multifamily residence limited density 8,000 sq ft Up to 17 units per acre
MF-2 Multifamily residence low density 8,000 sq ft Up to 23 units per acre
MF-3 Multifamily residence medium density 8,000 sq ft Up to 36 units per acre
MF-4 Multifamily residence moderate-high density 8,000 sq ft 36 to 54 units per acre
MF-5 Multifamily residence high density 8,000 sq ft Up to 54 units per acre
MF-6 Multifamily residence highest density 8,000 sq ft Multifamily, with no units-per-acre figure in the code
MH Mobile home residence No figure in the table Mobile home parks and subdivisions

Sources: Austin LDC 25-2-32, 25-2-492, 25-2-53 to 25-2-68, 25-2-558 and 25-2-779, Supplement 174. Units per acre are the figures in each district's designation section, which says they depend on unit size.

The Lake Austin district is tied to one place. Section 25-2-53 applies it to a lot of at least one acre that is 1,000 feet or less from the 492.8 foot contour line on either side of Lake Austin. A contour line joins points at the same height above sea level.

The Housing Uses the Code Defines

Austin sorts housing by use, and Section 25-2-3 defines each one. The number of homes and whether they share a building decide the use:

  • Single-family residential is one dwelling unit on a site. A dwelling unit is a home with its own space for living, sleeping, eating and cooking.
  • Small lot single-family residential is one dwelling unit on a small lot, which Section 25-1-21 defines as a lot of less than 5,750 square feet.
  • Duplex residential is "the use of a site for two dwelling units within a single building, other than a mobile home."
  • Two-unit residential is "the use of a lot for two dwelling units, each in a separate building, other than a mobile home." A house with a detached second home behind it is this use.
  • Three-unit residential is "the use of a lot for three dwelling units other than a mobile home." The City's HOME page says the three homes may be attached or detached in any combination.
  • Single-family attached residential is two joined homes, each on its own lot.
  • Townhouse residential is a group of homes joined by common walls, each on its own townhouse lot. Condominium residential is attached or detached condominiums, as the Texas Property Code defines them.
  • Multifamily residential is "the use of a site for four or more dwelling units, within one or more buildings."

The definitions leave no use for exactly four homes on a single-family lot. Three homes is the three-unit use. Four homes is multifamily use, which belongs to the MF districts.

Which Use Is Permitted in Which District

The table in Section 25-2-491 marks each use in each base district as permitted, conditional or prohibited. A permitted use is approved by City staff against the written rules. A conditional use needs a site plan approved by the Land Use Commission after a public hearing. Every housing use below is marked permitted in the districts shown.

Housing use Residential districts where it is permitted
Single-family residential (one home) LA, RR, SF-1, SF-2, SF-3, SF-5, SF-6 and MF-1 to MF-6
Small lot single-family residential SF-1, SF-2, SF-3, SF-4A, SF-4B, SF-5 and SF-6
Duplex residential SF-1, SF-2, SF-3, SF-5, SF-6 and MF-1 to MF-6
Two-unit residential SF-1, SF-2, SF-3, SF-5, SF-6 and MF-1 to MF-6
Three-unit residential SF-1, SF-2 and SF-3
Single-family attached residential SF-3, SF-5, SF-6 and MF-1 to MF-6
Townhouse residential SF-5, SF-6 and MF-1 to MF-6
Condominium residential SF-5, SF-6 and MF-1 to MF-6
Multifamily residential (four or more homes) MF-1 to MF-6

Source: Austin LDC 25-2-491(C), residential uses rows, Supplement 174. The table also permits several of these uses in the downtown districts CBD and DMU.

Two rows matter for a small project. Three-unit residential use is permitted in SF-1, SF-2 and SF-3 and nowhere else. Townhouse and condominium uses start at SF-5. So an owner in SF-5 or SF-6 has the townhouse and condominium rules to work with, and an owner in SF-1, SF-2 or SF-3 has the three-unit use. Section 25-2-492 sets the number of homes: its row "MAXIMUM DWELLING UNITS PER LOT" shows 1 for LA and RR and 3 for SF-1, SF-2 and SF-3.

The multifamily districts work by site area for each home. In MF-1, Section 25-2-560 requires 2,500 square feet of site for an efficiency unit, 3,000 for a one-bedroom unit and 3,500 for a unit with two or more bedrooms. An efficiency is a unit of not more than 400 square feet with no separate bedroom. MF-2 requires 1,600, 2,000 and 2,400 square feet. MF-3 requires 1,200, 1,500 and 1,800. MF-4 and MF-5 require 800, 1,000 and 1,200. On an 8,000 square foot MF-3 lot, that arithmetic gives four two-bedroom homes, because four times 1,800 is 7,200.

Combining Districts on Top of the Base Zone

A combining district is a second zone laid over the base district that adds or changes rules for the land it covers. Section 25-2-32 lists 31 of them. Four of them change the rules for single-family lots:

  • Neighborhood plan (NP). The ordinance that creates an NP district names special uses allowed in it. Section 25-2-1406 lets that ordinance reduce the minimum lot to 2,500 square feet and the width to 25 feet for a single-family use on an existing legal lot platted on or before August 15, 2024. The City's HOME page lists Small Lot Amnesty under its neighborhood plan infill tools and says: "Small Lot Amnesty only applies to single-family residential uses." The ordinance may also change the floor area limit and setback planes of Subchapter F.
  • Conditional overlay (CO). Under Section 25-2-332, the rules of a CO "must be more restrictive than the restrictions otherwise applicable to the property." A CO may decrease the number of dwelling units, increase the minimum lot size or width, decrease the height, or prohibit a use the base district permits.
  • Neighborhood conservation (NC). Section 25-2-371 says an NC district modifies the use and site rules of the base district in line with a neighborhood plan.
  • Historic landmark (H) and historic area (HD). These protect a single property or a whole area. They are covered in the next section.

Because a CO, NC or NP ordinance is written for one area, its text is the only place to learn what it changes. The three homes that SF-3 permits can be cut to fewer by a conditional overlay on the same lot. Read the zoning ordinance for your lot before you rely on the base district alone. Private deed restrictions are separate from zoning, and the City's deed restrictions page says zoning changes do not affect whether they can be enforced.

Historic Landmarks and Historic Districts

Section 25-2-352 lets the Council zone a structure or site as a historic landmark (H) when it is at least 50 years old, keeps a high degree of integrity, and meets the listing or significance tests in the section. The Council may zone an area as a historic area (HD) district if at least 51 percent of its principal structures contribute to its historic character. "The minimum size for a historic area (HD) combining district is one block face."

The base zoning stays, and a review is added. Under Section 25-11-212, a person needs a certificate of appropriateness, which is the Historic Landmark Commission's written approval, before changing the outside of a landmark or a contributing structure. The same certificate is needed to "construct a new, standalone, ground-up structure on a historic landmark (H) property or within a historic area (HD) combining district." A second or third home in an HD district is such a structure.

Older houses outside any district can also be reviewed. The City's Residential Plan Review page says a historic review is required for structures 45 years old or older where the exterior is being demolished or modified. Section 25-11-213 gives the historic preservation officer five business days to review a complete application and decide whether to send it to the Commission, and the Commission holds its hearing within 60 days. The building official then waits until the Commission acts, or until 75 days after the first Commission meeting where the application was on the agenda. For a contributing structure in a National Register Historic District, the wait is 180 days after a complete application. The FY 2026-27 fee schedule lists $395.00 for review of a total demolition of a principal residential building.

How a Rezoning Is Decided

A rezoning changes the base district of a property. Under Section 25-2-242 it may be started by the Council, the Land Use Commission or the record owner, and by the Historic Landmark Commission for historic zoning. The Land Use Commission is the Zoning and Platting Commission, or the Planning Commission for land inside an adopted neighborhood plan. The steps in Sections 25-2-282 and 25-2-283 are:

  1. The Land Use Commission holds a public hearing not later than the 60th day after the application is filed.
  2. The Commission makes its recommendation to the Council not later than the 14th day after it closes the hearing.
  3. The Council holds a public hearing not later than the 40th day after the date of that recommendation.
  4. The Council may approve the request, approve a more restrictive district, approve with conditions, or deny it.

One rule helps a small owner: "The council may not require a site plan as a condition of zoning or rezoning." Two rules set limits. Under Section 25-2-246 an application expires if the Council adopts no ordinance before the 361st day after it closes its hearing. Under Section 25-2-247, after a denial or a withdrawal the same request may not be filed again for 12 or 18 months, depending on how the first one ended.

Neighbors can raise the vote that is needed. Section 25-2-284 requires the vote of three-fourths of the Council members when a rezoning is protested in writing by the owners of at least 20 percent of the land in the change, or of the land next to it and extending 200 feet from it. State law changed in 2025. Local Government Code 211.0061, added by HB 24, raises the adjoining-land protest to 60 percent when the change "has the effect of allowing more residential development than the existing zoning regulation or district boundary," and a protest at that level is overcome by a majority of all members. Section 25-2-284 was last amended in 2016 and gives the 20 percent rule alone, so ask the City which vote applies to your case. The HB 24 page explains the state rule.

A rezoning also has City fees. The FY 2026-27 Zoning Plan Review schedule lists a regular rezoning of less than one acre at $2,651.96 for Austin Development Services, $1,098.42 for basic notification and $183.07 for newspaper notification, a subtotal of $3,933.45. The same row lists an Austin Planning fee of $9,030.00. The plats, permits and fees page has more.

Best For

  • ✓ A lot zoned SF-1, SF-2 or SF-3 with at least 5,750 sq ft, where three homes are a permitted use.
  • ✓ A lot zoned SF-5 or SF-6, where townhouses and condominiums are permitted uses.
  • ✓ An MF lot of 8,000 sq ft or more, sized by site area for each home.

Usually Fails When

  • ✕ The plan needs four homes on a lot zoned SF-1, SF-2 or SF-3.
  • ✕ A conditional overlay on the lot lowers the number of homes or the height.
  • ✕ The lot is in a historic area (HD) district and the new building is refused a certificate of appropriateness.

What To Verify Before Spending Money

  • → The base district and every combining district on the lot, in the City's Property Profile tool.
  • → The text of any CO, NC or NP ordinance that covers the lot.
  • → Which protest rule the City applies to a rezoning that adds homes.

Where to Go Next

Related on VanPlex: the Austin overview, how Texas zoning works, and SB 840 on housing in commercial zones.

Frequently Asked Questions

How do I find out what my Austin lot is zoned? +
The City of Austin points owners to its Property Profile tool to check the zoning of a property. The result is a map code from Section 25-2-32 of the Land Development Code, such as SF-3 for family residence, sometimes with a combining district code such as NP or CO added. The base code decides which housing uses the use table in Section 25-2-491 permits.
What does SF-3 zoning allow in Austin? +
SF-3 is Austin's family residence district. The use table in Section 25-2-491 permits single-family, small lot single-family, duplex, two-unit, three-unit and single-family attached uses there, and Section 25-2-492 sets a maximum of 3 dwelling units per lot. The district was written for lots of at least 5,750 square feet, and two or three homes need a lot of that size.
Can I build a fourplex on an SF-3 lot in Austin? +
A fourplex is outside what SF-3 allows in Austin. Section 25-2-3 defines multifamily residential use as four or more dwelling units on a site, and the use table permits that use in the MF-1 to MF-6 districts. In SF-1, SF-2 and SF-3 the limit is 3 dwelling units per lot, so a fourth home needs a rezoning to a multifamily district.
What is the difference between SF-2 and SF-3 in Austin? +
Austin's SF-2 and SF-3 districts share a 5,750 square foot minimum lot and a limit of 3 dwelling units per lot. The use table shows two differences: single-family attached residential use and small-site retirement housing are permitted in SF-3 and are absent from SF-2. Section 25-2-57 also describes SF-3 as a district for single-family and duplex use.
How many apartments can an MF-3 lot hold in Austin? +
An MF-3 lot in Austin is sized by site area per home under Section 25-2-562: 1,200 square feet for an efficiency, 1,500 for a one-bedroom unit and 1,800 for a unit with two or more bedrooms. Section 25-2-64 describes the district as allowing up to 36 units per acre, depending on unit size. The minimum lot is 8,000 square feet.
What does NP mean at the end of an Austin zoning code? +
NP is the map code for a neighborhood plan combining district in Austin. The ordinance that creates one names the special uses allowed there, such as cottage lots of at least 2,500 square feet or urban home lots of at least 3,500 square feet. Under Section 25-2-1406 it may also change the floor area limit of Subchapter F for that area.
What is a conditional overlay in Austin zoning? +
A conditional overlay, map code CO, is a combining district that adds limits to one property. Section 25-2-332 says its rules must be more restrictive than the rules that would otherwise apply. A CO may decrease the number of dwelling units, increase the minimum lot size, decrease the height or prohibit a use, so read the zoning ordinance for the lot.
How long does a rezoning take in Austin? +
Austin's code sets three time limits for a rezoning. The Land Use Commission holds a hearing not later than the 60th day after filing and recommends within 14 days of closing it. The Council holds its hearing not later than the 40th day after that recommendation. Under Section 25-2-246 an application expires if Council adopts no ordinance before the 361st day after it closes its hearing.
Can neighbors block a rezoning in Austin? +
Neighbors in Austin can raise the vote a rezoning needs. Under Section 25-2-284, a written protest by owners of 20 percent of the land in the change, or within 200 feet of it, means three-fourths of the Council members must approve. Texas Local Government Code 211.0061, added in 2025, sets a 60 percent protest level for changes that allow more homes.
Does a historic district stop me from adding homes in Austin? +
A historic district in Austin adds a review and leaves the base zoning in place. Section 25-11-212 requires a certificate of appropriateness before anyone builds a new standalone structure on a historic landmark property or inside a historic area (HD) combining district. The City's FY 2026-27 fee schedule lists the certificate application at $50.00, on top of plan review and permit fees.

Official sources (checked October 2026)

Austin LDC 25-2-32, zoning districts and map codes
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_AZOUSDIMADIDE_ART2ZODI_DIV1DIGE_S25-2-32ZODIMACO
Austin LDC 25-2-3, residential uses described
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_AZOUSDIMADIDE_ART1ZOUS_S25-2-3REUSDE
Austin LDC 25-2-491, permitted, conditional and prohibited uses
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_CUSDERE_ART2PRUSDERE_DIV1RETA_S25-2-491PECOPRUS
Austin LDC 25-2-492, site development regulations
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_CUSDERE_ART2PRUSDERE_DIV1RETA_S25-2-492SIDERE
Austin LDC Chapter 25-2, Subchapter C, Article 3, Division 1, residential district regulations
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_CUSDERE_ART3ADRECEDI_DIV1REDI
Austin LDC 25-2-332, conditional overlay combining district regulations
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_BZOPRSPRECEDI_ART2SPRECEDI_DIV2COOVCODI_S25-2-332COOVCOCODIRE
Austin LDC 25-2-352, historic designation criteria
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_BZOPRSPRECEDI_ART2SPRECEDI_DIV3HILAHIARDI_S25-2-352HIDECR
Austin LDC 25-2-1406, neighborhood plan combining district ordinance requirements
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_DNEPLCODI_ART1GEPR_S25-2-1406ORRE
Austin LDC 25-11-212, certificate of appropriateness required
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-11BUDEREPESPREHIST_ART4SPREHIST_DIV1HISTGE_S25-11-212CERE
Austin LDC 25-11-213, permits for historic buildings, structures and sites
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-11BUDEREPESPREHIST_ART4SPREHIST_DIV1HISTGE_S25-11-213BUDEREPECEAPRECEBUSTSI
Austin LDC Chapter 25-2, Subchapter B, Article 1, Division 4, rezoning hearings and action
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_BZOPRSPRECEDI_ART1ZOPRGE_DIV4PUHEAC
Austin LDC 25-2-284, approval by three-fourths of Council
https://library.municode.com/tx/austin/codes/land_development_code?nodeId=TIT25LADE_CH25-2ZO_SUBCHAPTER_BZOPRSPRECEDI_ART1ZOPRGE_DIV4PUHEAC_S25-2-284REAPTHURCO
City of Austin, HOME amendments
https://www.austintexas.gov/development-services/home-amendments
City of Austin, deed restrictions and development
https://www.austintexas.gov/development-services/deed-restrictions-and-development
City of Austin Development Services, fee schedules for FY 2026-27
https://www.austintexas.gov/development-services/fees
City of Austin, Zoning Plan Review fee schedule (PDF)
https://austin.widen.net/s/lvdcfhcdtd/fees_zoning
City of Austin, Historic Preservation Review fee schedule (PDF)
https://austin.widen.net/s/drfspmhfd2/fees_historic
Local Government Code 211.0061 (zoning protest procedures)
https://statutes.capitol.texas.gov/Docs/LG/htm/LG.211.htm#211.0061
VanPlex newsletter

Get new guides by email

New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.

General information, not legal advice. Texas has no statewide zoning code. Each city writes its own rules, and deed restrictions recorded on a lot can forbid what the city allows. Confirm current requirements with the city planning department, read the deed restrictions for your lot, and talk to a Texas-licensed attorney or architect before you buy land or file plans.

Planning a multiplex in Austin?

VanPlex builds multiplexes in British Columbia, Canada. For a lot in Austin, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.

Get a proforma for your address