Austin | Watersheds, Trees and Floodplain
Austin Watersheds, Save Our Springs, Protected Trees and Floodplain Rules
Three sets of rules can shrink what the zoning allows on an Austin lot. The watershed rules in Chapter 25-8 of the Land Development Code (LDC) cap paved and roofed area by the creek a lot drains to, as low as 15 percent over the aquifer that feeds Barton Springs. The tree rules protect any tree of 19 inches across. And the drainage rules in Chapter 25-7 keep new buildings out of the 100-year floodplain. This page explains each set and what it means for two or three homes. The Austin overview gives the short version.
Austin watersheds, trees and floodplain in six facts
- In the watersheds that contribute to Barton Springs, impervious cover is limited to 15 percent in the recharge zone and 20 or 25 percent in the contributing zone. Source: Austin LDC 25-8-514
- That limit does not apply to a single-family, single-family attached or duplex structure on one platted lot that existed on November 1, 1991. Source: Austin LDC 25-8-516
- A protected tree has a trunk diameter of 19 inches or more, measured four and one-half feet above natural grade. Source: Austin LDC 25-8-602
- A heritage tree is one of ten listed kinds, such as all oaks and pecans, with a diameter of 24 inches or more, and removing one needs a variance. Source: Austin LDC 25-8-602 and 25-8-641
- A development application may not be approved if a proposed building or parking area encroaches on the 100-year floodplain, except as the code allows. Source: Austin LDC 25-7-92
- A replacement home in the floodplain must sit no lower than two feet above the 100-year floodplain and may not add legal dwelling units. Source: Austin LDC 25-7-93
Watersheds and Why They Matter
A watershed is all the land that drains to one creek or lake. Austin's code sorts its watersheds into five classes and sets lower limits on paving in the classes that feed drinking water. Section 25-8-2 names them: urban, suburban, water supply suburban, water supply rural, and the Barton Springs Zone. It also defines the Edwards Aquifer, the water-bearing rock under the west side of the city, and its recharge zone, "all land over the Edwards Aquifer that recharges the aquifer." The contributing zone is the land west and upstream of the recharge zone that drains into it.
The section says a map of these areas is kept by the Watershed Protection Department "and made available for reference online and at the offices of the Development Services Department." The director decides the boundaries, and for land within 1,500 feet of an Edwards Aquifer recharge zone boundary may require a certified report from a geologist or hydrologist to confirm the line.
The limits below are on impervious cover, the total area of any surface that stops water from soaking into the ground, such as roofs, driveways and concrete. The zoning table gives one limit. The watershed rules give another. Section 25-2-492 says that where its table conflicts with another provision of the title, "the more restrictive regulation governs," so the lower figure is the one a design must meet.
Impervious Cover Limits by Watershed
| Watershed class | Examples in the code | Limit for homes in the uplands zone |
|---|---|---|
| Urban watersheds | Boggy, Shoal, Waller, Johnson, Little Walnut and other central creeks | The zoning limit in Section 25-2-492 (45 percent in SF-2 and SF-3) |
| Suburban watersheds, zoning jurisdiction outside five named creeks | Walnut, Onion and Williamson outside the aquifer zones, and others | 50 percent on lots of 5,750 sq ft or more; 55 percent for a duplex or single-family lot under 5,750 sq ft |
| Suburban watersheds in the ETJ and in Lake, Rattan, Buttercup, South Brushy and Brushy Creeks | Those five creeks and land outside the city limits | 45 percent on lots of 5,750 sq ft or more; 55 percent under 5,750 sq ft |
| Water supply suburban watersheds | Bull, Eanes, West Bull and parts of the Lady Bird Lake and Lake Austin watersheds | 30 percent of net site area for a duplex or single-family use |
| Water supply rural watersheds | Lake Travis, the Lake Austin watershed apart from listed parts, and listed creeks | One home for each two acres, with a minimum lot of three-quarters of an acre |
| Barton Springs Zone | Barton Creek and the creeks that recharge Barton Springs | 15 percent in the recharge zone; 20 percent in the Barton Creek contributing zone; 25 percent in the rest of the contributing zone |
Sources: Austin LDC 25-8-2, 25-8-372, 25-8-392, 25-8-423, 25-8-453 and 25-8-514, Supplement 174. The suburban figures can rise by 5 to 10 points where development intensity is transferred under the code.
The uplands zone is the land away from the creeks. Near the creeks the limits are tighter, as the next section explains. Two points in the table matter for small projects. In the urban watersheds, such as Boggy, Shoal and Waller Creeks, the watershed rule adds no limit beyond the zoning table. And in the water supply suburban watersheds, such as Bull and Eanes Creeks, a duplex or single-family use may cover only 30 percent of the net site area, 15 points under the 45 percent the zoning table allows in SF-3.
When a subdivision is planned, the City assumes a figure for each lot. Under Section 25-8-64, a duplex or single-family lot of more than 5,750 and not more than 10,000 square feet is assumed to carry 2,500 square feet of impervious cover. A lot of not more than 5,750 square feet is assumed to carry the maximum its zoning allows. The section adds that it "does not restrict impervious cover on an individual lot," apart from a lot restricted to less.
Creek Buffers: Critical Water Quality Zones
Along each creek the code draws a critical water quality zone. Section 25-8-91 classes a creek by the land that drains to it: a minor waterway drains 64 to 320 acres, an intermediate one more than 320 and up to 640, and a major one more than 640. In an urban watershed the zone follows the 100-year floodplain of any creek draining at least 64 acres, and is never less than 50 feet or more than 400 feet from the center of the creek. In the suburban watersheds the zone is 100, 200 or 300 feet from the center line for a minor, intermediate or major waterway.
Section 25-8-261 sets the rule: "In all watersheds, development is prohibited in a critical water quality zone except as provided in this Division." The exceptions are fences that do not block flood flows, trails, some open space, and docks on the lakes. No exception covers a home. In the water supply watersheds and the Barton Springs Zone, a second band called the water quality transition zone runs beside it, 100, 200 or 300 feet wide. In the Barton Springs Zone, Section 25-8-482 limits homes in that band outside the recharge zone to lots of at least two acres, at one home for each three acres.
On the lakes the zone is measured from a set contour line. For Lady Bird Lake the line is the 429.0 foot contour and for Lake Austin the 492.8 foot contour. The zone runs 100 feet inland, or 75 feet for a detached single-family residential use.
Save Our Springs
Article 13 of Chapter 25-8 is the Save Our Springs Initiative. It "codifies the Save Our Springs Initiative Petition Ordinance as adopted by popular vote on August 8, 1992." It covers the watersheds that contribute to Barton Springs, and Section 25-8-512 says it "may be repealed or amended only by an affirmative vote of a three-quarters majority of the city council."
Section 25-8-514 holds the limits: "impervious cover for all such development shall be limited to a maximum of 15 percent in the entire recharge zone, 20 percent of the contributing zone within the Barton Creek watershed, and 25 percent in the remainder of the contributing zone." The limits are measured on net site area. Runoff must also be managed so that the yearly loads of ten kinds of pollution leaving the site do not rise. Section 25-8-515 says the article is not subject to the exemptions, waivers or variances that the rest of the chapter allows.
The exemption in Section 25-8-516 matters for infill lots. The article "does not apply to development on a single platted lot or a single tract of land that is not required to be platted before development if the lot or tract existed on November 1, 1991" and the development is either of two things:
- building, renovating or adding to "a single-family, single-family attached, or a duplex structure used exclusively for residential purposes," with the improvements that go with that use; or
- development of a maximum of 8,000 square feet of impervious cover, counting what existed before and after.
The list in the first branch was written in 1992 and names no two-unit or three-unit use. Three detached homes on an old lot therefore rely on the second branch, and stay exempt only while all roofs and paving together stay at or under 8,000 square feet. A lot platted after November 1, 1991 is under the 15, 20 or 25 percent limits whatever is built. Ask the Watershed Protection Department how it reads the first branch for a two-unit use before you design to it.
Water Quality Controls
A water quality control is a pond, filter or similar structure that cleans runoff before it leaves a site. Section 25-8-211 requires them for all development in the Barton Springs Zone. In the other watersheds they are required for development in a water quality transition zone, for golf courses and fields where chemicals are applied, or "if the total of new and redeveloped impervious cover exceeds 8,000 square feet." The section adds: "The water quality control requirements in this division do not require water quality controls on a single-family or duplex lot but apply to the residential subdivision as a whole." A small subdivision may therefore need a control for the whole plat even though each lot does not.
Protected and Heritage Trees
Section 25-8-602 defines two kinds of tree, both measured four and one-half feet above natural grade:
- Protected tree. Any tree "with a diameter of 19 inches or more."
- Heritage tree. A tree with a diameter of 24 inches or more that is one of ten kinds: Texas ash, bald cypress, American elm, cedar elm, Texas madrone, bigtooth maple, all oaks, pecan, Arizona walnut and eastern black walnut.
Removal means any act that can be expected to kill the tree, including damage to the roots and too much pruning. Under Section 25-8-621, a protected tree may not be removed without a permit, unless it is a damaged tree that is an imminent hazard and is removed within seven days, or it is marked for removal on an approved plan or plat. Section 25-8-624 allows a permit only when the tree prevents reasonable access to or use of the property, is an imminent hazard that cannot be fixed another way, is dead, or is diseased beyond repair. On private land, the applicant must first ask for a variance, waiver or other change that would save the tree, and the permit may be approved only if that request is denied. Mitigation, such as planting replacement trees, is a condition of every approval. The City acts on a complete application within 10 working days.
A heritage tree is harder to remove. Section 25-8-641 prohibits removal without a permit, and the permit may be issued only after a variance. The director may grant one for a dead, hazardous or diseased tree with no fee and no mitigation. For a healthy tree, the director decides if no stem is 30 inches or larger, and the Land Use Commission decides if one is, after review by the Environmental Commission. In both cases the applicant must first have been denied another code change that would save the tree, and the removal may not come from a condition the applicant's chosen design created, unless the design that results gives the most ecological, historic and cultural value.
Two smaller rules apply too. Under Section 25-8-604, a site plan application must show a design that keeps trees eight inches or larger in diameter "to the extent feasible," and the City may require mitigation for removing one. And under Section 25-5-2(D), the site plan exemption for small construction of up to 1,000 square feet is lost if a tree larger than eight inches in diameter is removed. Lay out a project on a lot with a large oak around the tree from the start.
| Tree and flood review fee | FY 2026-27 amount |
|---|---|
| Tree plan review, residential | $566.93 |
| Tree inspection, residential new construction | $449.75 |
| Tree pre-development consultation, residential | $542.42 |
| Heritage tree variance, administrative | $1,213.58 |
| Heritage tree variance, commission | $5,071.62 |
| Initial floodplain review (Watershed Protection) | $110.00 |
| Detailed floodplain review of a residential building plan | $470.00 |
| Residential floodplain variance, administrative | $1,431.00 |
Sources: City of Austin Tree Review and Inspection Fees and Residential Building Plan Review and Inspection Permit Fees, both updated and effective October 1, 2026, read October 8, 2026.
Floodplain Rules
Section 25-7-92 uses two floodplains. Section 25-7-2 defines the 100-year floodplain as an area with "a one percent or greater chance of flooding in any year," and the 25-year floodplain as one with a four percent or greater chance. The 25-year floodplain is calculated under fully developed conditions, using Atlas 14 rainfall data where the City has adopted it. A development application may not be approved if a proposed building or parking area encroaches on the 25-year floodplain, or on the 100-year floodplain, apart from listed exceptions.
Section 25-7-93 lists the exceptions. The one that reaches homes is "a new building for residential use that replaces an existing legally constructed building for residential use on the same property and that does not increase the number of legal dwelling units on the property." The new building must be no lower than two feet above the 100-year floodplain, measured from its lowest floor, must make up for the flood volume it displaces, and may not add flooding on other property. The director may also grant a variance on findings that include a finished floor two feet above the 100-year floodplain and conditions unique to the site.
For a HOME project this means a second or third home needs ground outside both floodplains or a variance, because the exception covers a replacement home that adds no legal dwelling units. The site plan exemption for four or fewer homes in Section 25-5-2 also requires the work to be outside the 100-year floodplain, or a finding that its effect on the waterway is insignificant. The City's Residential Plan Review page says a floodplain review is required if the property is inside the City's 100-year floodplain or within 100 feet of its boundary. The insurance and flood page covers flood insurance.
Drainage for Residential Infill
Section 25-7-61 sets the general drainage test for a development application, including on-site control of the two-year peak flow and no added flooding on other property. In 2025 the Council eased it for small infill work with Ordinance No. 20250306-037, which took effect on May 23, 2025. The new Section 25-7-67 says a residential infill project need not meet Sections 25-7-61, 25-7-151 or 25-7-152 if it is a resubdivision of no more than 17,780 square feet of gross site area, or if a drainage plan shows that all runoff will go to an existing storm drainage system or into the right-of-way. Improvements must still stay outside the erosion hazard zone, the land where creek banks are expected to wear away.
The City's HOME amendments page explains the effect on a building permit: "If your lot was created before June 16, 2025, and you're building no more than four units, then no drainage review is required." A lot created after that date and approved with a grading plan under Section 25-7-67 must follow that plan, and may need to be graded so runoff runs to the street before a certificate of occupancy is issued. The Residential Plan Review page adds a separate trigger: a grading and drainage review is required when a storm inlet is within 10 feet of a driveway curb cut.
Best For
- ✓ A lot in an urban watershed, where the uplands cover limit is the zoning figure of 45 percent in SF-2 and SF-3.
- ✓ A lot platted before November 1, 1991 over the Barton Springs Zone, with 8,000 sq ft or less of total cover.
- ✓ A lot created before June 16, 2025 with four or fewer homes, which needs no drainage review.
Usually Fails When
- ✕ The second or third home would stand in the 25-year or 100-year floodplain.
- ✕ A heritage tree sits where the new home must go and no other code change can save it.
- ✕ The lot is in a water supply suburban watershed, where homes may cover 30 percent of the net site area.
What To Verify Before Spending Money
- → The watershed class and aquifer zone of the lot on the Watershed Protection Department map.
- → The diameter and kind of every tree of 19 inches or more, measured four and one-half feet above grade.
- → Whether the lot is inside the 100-year floodplain or within 100 feet of it.
Where to Go Next
Related on VanPlex: the Austin overview, insurance and flood in Texas, and SB 15 and its exception for aquifer rules.
Frequently Asked Questions
What is the Save Our Springs ordinance in Austin?
Does Save Our Springs stop me from adding a second home on my Austin lot?
How do I find out which watershed my Austin lot is in?
What is a protected tree in Austin?
Can I remove a heritage tree to build in Austin?
How long does Austin take to decide a tree removal permit?
Can I build a new home in the 100-year floodplain in Austin?
What does the 100-year floodplain mean in Austin's code?
Does a residential infill lot in Austin need detention for stormwater?
Do I need water quality controls for a duplex lot in Austin?
Official sources (checked October 2026)
Get new guides by email
New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.
Planning a multiplex in Austin?
VanPlex builds multiplexes in British Columbia, Canada. For a lot in Austin, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.
Get a proforma for your address