David Babakaiff
Written by David Babakaiff · Co-Founder, VanPlex | 25+ Years BC Construction Last reviewed: October 2026

San Antonio | Three or More Homes

San Antonio Triplexes, Fourplexes, Townhouses and Infill: Three or More Homes on a Lot

This page covers seven routes to three or more homes on one site under San Antonio's Unified Development Code (UDC). The RM-5 and RM-4 districts allow a triplex or fourplex on an ordinary city lot. Section 35-373 sets rules for townhouses and cottage housing. The Infill Development Zone (IDZ) and Section 35-312, San Antonio's version of the state law SB 840, allow more. This page gives the numbers for each route. The San Antonio overview gives the short version.

Three or more homes in San Antonio, in six facts

The Seven Routes

Route Where it is allowed Main number UDC section
Triplex (three-family dwelling) RM-5, RM-4 and all MF districts 3 units on an RM-5 lot of 5,000 sq ft or more 35-310.06, Table 311-1
Fourplex (four-family dwelling) RM-4 and all MF districts 4 units on an RM-4 lot of 4,000 sq ft or more 35-310.06, Table 311-1
Townhouses R-6, R-5, R-4, R-3, R-2, R-1, RM and MF districts Lots of 1,200 sq ft and 15 ft wide, up to 40 units per gross acre 35-373(b)
Cottage housing development RM-6, RM-5, RM-4 and IDZ Site of 11,600 sq ft or more, cottages of up to 975 sq ft 35-373(d)
Multi-family (5 or more units) MF-18 to MF-65 18 to 65 units per acre Table 310-1, Table 311-1
Infill Development Zone Land rezoned to IDZ-1, IDZ-2 or IDZ-3 18 units per acre, 50 units per acre, or a density stated in the ordinance 35-343.01
Housing on commercial land O-1, O-1.5, O-2, NC, C-1, C-2, C-3, L and listed mixed-use districts Up to 65 units per acre, no rezoning 35-312

Source: San Antonio UDC sections named in the last column, Supplement 25 Update 1, read through 35-311, 35-373, 35-343.01 and 35-312.

The first four routes need no public vote when the lot already has the right zoning. IDZ needs a rezoning, a change of zoning district, by City Council. A rezoning from an R district to RM-5, RM-4 or MF is also a Council decision, and the zoning districts page covers the steps and the vote.

Triplexes and Fourplexes in RM-5 and RM-4

Appendix A defines a three-family dwelling (triplex) and a four-family dwelling (quadraplex) the same way: a "detached structure (on a platted single lot) with common walls or common floor/ceiling between the units," for no more than three or four families, "each living as an independent housekeeping unit." A plat is the recorded map that creates lots.

Section 35-310.06 sets the count. The table density of 9 units per acre in RM-5 and 11 in RM-4 may be exceeded when the lot meets the district minimum, and the number of dwellings "is limited to two (2) units for RM-6, three (3) units for RM-5, and four (4) units for RM-4." These limits came from Ordinance No. 2022-11-03-0831, effective January 1, 2023.

Rule RM-5 RM-4
Minimum lot 5,000 sq ft 4,000 sq ft
Most dwellings on the lot 3 4
Street frontage and lot width 15 feet each 15 feet each
Maximum lot width (detached houses only) 100 feet 80 feet
Front setback 10 feet 10 feet
Side setback 5 feet 5 feet
Rear setback 10 feet 10 feet
Height 35 feet, 3 stories 35 feet, 3 stories
Largest single building 65% of lot area 65% of lot area
Parking, three or four-family 1.5 to 2 spaces per unit 1.5 to 2 spaces per unit

Sources: San Antonio UDC Table 310-1, 35-310.06 and Table 526-3a, Supplement 25 Update 1.

A setback, in the table above, is the distance a building must keep from a lot line. Three design rules apply on a lot of one-third of an acre (14,520 square feet) or smaller:

  • One building. Multi-unit construction "shall be within a single structure." Three or four separate small houses on one RM lot do not meet this rule.
  • Front entry. Note 13 of Table 310-1 says construction of two to four units "shall have a front entry oriented to the primary street in which the lot is addressed on," and a "front walkway from the door shall also be provided."
  • Front yard paving. Table 515-1 limits driveways and other impervious surfaces to 50 percent of the front yard in the RM districts. Impervious means a surface that water cannot pass through, such as concrete.

Table 526-3a sets the parking: a minimum of 1.5 spaces per unit and a maximum of 2 for a three-family or four-family dwelling. A fourplex needs 6 spaces. A triplex comes to 4.5, and Section 35-526(i) says that when fewer than five spaces are required, "a full parking space shall be required to fulfill a fractional space requirement," so the triplex needs 5. Each space is at least 9 feet by 18 feet. A parking area with three or more spaces must include a turnaround so that cars "can enter and exit the parking area without backing onto a public right-of-way."

Permits for Three and Four Units

Appendix A keeps the term multi-family for "five (5) or more families," so the UDC term does not cover a triplex or fourplex. The permit path is a separate question. Section 10-36 of the City Code adopts the "International Residential Code for One-and-Two-family Dwellings," and the City's Information Bulletin 101 lists the homes that use a New Residential Permit as "All single-family, two-family (duplex), and townhomes (not more than three stories above grade plane with separate means of egress)." A building with three or four stacked units is not on that list. The building codes page explains the line between the residential and commercial codes in Texas.

Information Bulletin 225, "Multiple Dwelling Units on One or More Lots," says when a project also needs a Site Work Permit, which is filed on the Commercial Project Application. A separate Site Work Permit is needed when:

  • "Three or more dwelling units are being proposed for construction on a single platted lot where one or more homes do not front a public or private street."
  • Two or more dwelling units are proposed, each on its own platted lot, where one or more lots front an ingress/egress easement, a recorded right to cross a strip of land.

The bulletin lists other cases: a site over the Edwards Recharge Zone District, shared parking spaces, a single fire line serving several units, and homes that tie into private utilities. It says a townhome development with each unit facing a platted street does not need the separate permit.

One tree rule changes between three and four units. Section 35-523(a)(4) exempts trees on property "on which construction of single-family, two-family or three-family residential dwelling units has been completed." The exemption does not name four-family dwellings, so ask the City arborist how the tree rules apply to a finished fourplex.

The MF Districts

All six MF districts permit two, three and four-family dwellings by right, which means City staff approve them against the written rules with no public vote. Each district adds apartments up to its own density: 18, 25, 33, 40, 50 or 65 units per acre. Section 35-310.07 describes MF-18 and MF-25 as districts that "may be used as a transition between a single-family and higher intensity uses."

Table 310-1 handles MF land differently from RM land. An MF lot needs 50 feet of frontage, the lot edge along the street, and 50 feet of width, and the table lists no minimum lot size. The table sets a maximum front setback of 20 feet and lists no minimum; Note 6 extends the maximum to 90 feet on a lot with 100 feet or more of street frontage. The side setback is 5 feet and the rear is 10 feet. Height is 35 feet in MF-18 and MF-25, 45 feet in MF-33 and 60 feet in MF-40; the table lists no height for MF-50 and MF-65.

Three notes protect houses next door:

  • Rear setback of 40 feet. An MF-18 to MF-50 district "adjoining a platted subdivision zoned single-family residential use shall have a minimum rear setback of forty (40) feet," and parking must be at least 5 feet from any fence on the rear line.
  • Height within 50 feet. Under Note 11, any part of a multi-family district within 50 linear feet of the property line of "an established single-family residential use" is limited to the maximum height of the single-family district.
  • Small MF-33 lots. On an MF-33 lot of one-third of an acre or smaller, the units must be in a single structure, and Note 12 sets the front setback equal to that of an abutting lot with a single-family use.

Parking for multi-family dwellings is 1.5 spaces per unit at the least and 2 at the most. Section 35-310.07 allows up to 10 percent more units per acre in MF-40, MF-50 and MF-65 when the required parking is in a parking garage.

Townhouses

A townhouse is a "single-family dwelling unit constructed in a group of three (3) or more attached units in which each unit extends from foundation to roof." Each one is on its own lot, so it can be sold on its own. Table 311-1 permits townhouses by right from R-6 through the MF districts, which gives R-zoned land a route to three or more attached homes. Section 35-373(b) sets the rules:

  • "No front yard or side yard is required."
  • No rear setback is required when the lot abuts an alley or driveway at least 24 feet wide that serves the development. Otherwise "a twelve-foot rear setback shall be required."
  • "The minimum lot area shall be one thousand two hundred (1,200) square feet," and the minimum lot width "shall be fifteen (15) feet."
  • Each lot needs 100 square feet of contiguous open area, which may be lawn, landscaping or walkways and may not be parking or driveway.
  • "Except in the "TOD" district, no townhouse development shall exceed a density of more than forty (40) units per gross acre."
  • Each townhouse needs an attached garage, a detached garage, or a common parking lot for the development. Parking is not required in an approved IDZ district.
  • A townhouse may have three floors, or four in an approved IDZ district or the downtown (D) district.

Townhouses "shall not be subject to the minimum lot size for RM districts in Table 310-1." The plat must carry the words "townhouse subdivision," and Section 35-515(f) requires deed restrictions, private rules recorded with the land, that limit the lots to townhouse use and provide for upkeep of shared areas. Table 526-3a asks for 1 parking space per townhouse. The 20-foot garage setback in Section 35-516(g) "does not apply to townhouses."

Cottage Housing Developments

Section 35-373(d) allows a group of small detached houses on one site, which it calls a cottage housing development (CHD). A cottage is "a single-family detached dwelling which meets the requirements of this section." The density depends on the district.

Zoning district Land per unit (sq ft) Dwelling units per acre
IDZ 2,900 15
RM-4 3,300 13
RM-5 3,900 11
RM-6 4,800 9

Source: San Antonio UDC 35-373(d)(1), Supplement 25 Update 1.

  • Site. "The minimum lot area for a CHD shall be eleven thousand six hundred (11,600) square feet."
  • Height. Cottages "shall not exceed eighteen (18) feet or one and one-half (1½) stories in height." The ridge of a pitched roof may reach 25 feet.
  • Size. The main floor of a cottage may not exceed 800 square feet. Total floor area may not exceed 1.5 times the main floor or 975 square feet, whichever is less.
  • Coverage. Buildings may cover no more than 40 percent of the site.
  • Yards. The front yard averages 10 feet and is never less than 5. The rear yard is 10 feet and side yards are 5 feet.
  • Open space. The section requires "a minimum of four hundred (400) square feet per unit of common open space." At least 50 percent of the cottages must abut it, and every cottage must be within 60 feet walking distance of it.
  • Parking. Parking may not be in the front yard and must be screened from direct street view.

An 11,600 square foot RM-4 site at 3,300 square feet per unit holds three cottages. An existing house or duplex on the site may stay.

The Infill Development Zone

Section 35-343.01 covers IDZ zoning requests filed after November 1, 2018. Its purpose is "to encourage and facilitate development on vacant, bypassed lands, or the redevelopment of underutilized buildings or structures, within existing built-up areas." An IDZ may be located in the Community Revitalization Action Group (CRAG) target area, which Appendix A describes as the "thirty-six (36) square mile territory located inside the 1940 San Antonio corporate boundaries." It may also be located in a census tract inside Interstate Loop 410 where two of three conditions are present: at least 10 percent of structures are abandoned, at least 10 percent of platted lots are vacant, or at least 10 percent of lots or structures are subject to tax liens, which are legal claims for unpaid taxes.

  • IDZ-1. Limited to "no more than eighteen (18) dwelling units per acre." Height is limited to 2.5 stories and 35 feet. The minimum parking rules do not apply.
  • IDZ-2. Limited to "no more than fifty (50) dwelling units per acre." Height is limited to four stories. Minimum parking may be reduced by 50 percent.
  • IDZ-3. Any residential density, but "the density must be stated in the application and ordinance." Height is not limited, and minimum parking may be reduced by 50 percent.

A request for IDZ as a base district, the main zone on the land, comes with a list of permitted uses and a zoning site plan, a drawing of what will be built, which the Zoning Commission reviews and City Council approves with the rezoning. Next to a single-family use or zone, a building within 50 feet may not exceed 2.5 stories or 35 feet. In IDZ-1 the front setback must be "within ten (10) percent of the median setback of existing buildings on the block face." No building may come within 5 feet of the rear lot line or a perimeter side lot line.

The district removes several costs. Lots may be platted "without a minimum lot area requirement," and without street frontage if access is shown on the plat. The traffic impact study does not apply. The parks and open space standards do not apply. The stormwater management standards do not apply to "an existing parcel or lot of less than ten thousand (10,000) square feet." The City's FY 2027 Development Fee Schedule lists the storm water participation fee for "Infill Development Zone (IDZ) - all land uses" as "No fee," against $0.20 per square foot of impervious cover for multi-family land.

Housing on Commercial Land: Section 35-312

Section 35-312, added by Ordinance No. 2025-09-04-0580 on September 4, 2025, puts the state law SB 840 into the UDC. It defines multifamily residential for this purpose as "three or more dwelling units within one or more buildings," and mixed-use residential as a site where residential uses are "at least sixty-five (65) percent of the total square footage."

A property "may be developed as mixed use residential or a multifamily residential use if the property is zoned office, commercial, infill development zone, light industrial, business park, or mixed use, without needing to rezone." The section names the districts: O-1, O-1.5 and O-2; NC, C-1, C-2 and C-3; L light industrial; and MXD, IDZ and MPCD where they permit a mix of uses, the transit-oriented districts, BP and the AE arts and entertainment districts. The standards are:

  • A density of "no more than sixty-five (65) dwelling units per acre."
  • Height equal to the base district limit "or forty-five (45) feet, whichever is greater."
  • Setbacks equal to the base district limit "or twenty-five (25) feet, whichever is less."
  • Parking of "no more than one (1) required off-street parking space per dwelling unit."
  • No floor to area ratio limit, which is a limit on building floor area compared with lot area, and no requirement to include non-residential uses.

Five kinds of land are left out: land zoned for heavy industrial use; land within 1,000 feet of an existing heavy industrial use or site; land within "three thousand (3,000) feet of an airport or military base"; land in the military airport overlay zone (MAOZ), a second set of zoning rules near military runways; and a City-designated clear zone or accident potential zone. The UDC names Lackland Air Force Base, Randolph Air Force Base, Camp Bullis and Martindale Army Air Field in its military overlay sections, so check the distance early.

Subsection (e) covers turning an existing building into homes. A building used for office, commercial, retail or warehouse that "was constructed at least five (5) years before the proposed date of conversion" and will be at least 65 percent residential cannot be required to provide a traffic impact analysis, a study of the traffic the project adds, pay a traffic mitigation fee, or add parking beyond the spaces already on the site. The City keeps its rules on short term rentals, water quality, building codes, stormwater and historic preservation. Table 311-2 carries a matching row for attached apartments and condominiums at a maximum of 65 dwellings per gross acre, marked "See 35-312."

Best For

  • ✓ An RM-4 lot of 4,000 sq ft or more with room for 6 parking spaces behind or beside one building.
  • ✓ Three or more townhouses on R-zoned land, each on a platted lot of 1,200 sq ft or more.
  • ✓ A commercially zoned site more than 3,000 feet from an airport or military base.

Usually Fails When

  • ✕ The plan puts three or four separate houses on one RM lot of one-third of an acre or less.
  • ✕ A fourplex is planned on RM-5 or RM-6 land, where the limit is three or two units.
  • ✕ A Section 35-312 project sits in a military airport overlay zone or near heavy industry.

What To Verify Before Spending Money

  • → Whether the building is reviewed under the residential or the commercial building code.
  • → Whether Information Bulletin 225 requires a separate Site Work Permit for the layout.
  • → For IDZ, whether the lot is inside the CRAG area or a qualifying census tract inside Loop 410.

Where to Go Next

Related on VanPlex: the San Antonio overview, SB 840 in Texas, and building codes from duplex to fourplex.

Frequently Asked Questions

Can I build a triplex in San Antonio? +
San Antonio allows a triplex, which the UDC calls a three-family dwelling, by right in RM-5, RM-4 and the MF districts under Table 311-1. Section 35-310.06 limits an RM-5 lot to three units and requires the 5,000 square foot district minimum. On a lot of one-third of an acre or smaller, the three units must be within a single structure.
How much parking does a fourplex need in San Antonio? +
San Antonio UDC Table 526-3a requires at least 1.5 parking spaces per unit for a four-family dwelling and allows no more than 2 per unit, so a fourplex needs 6 spaces and may have 8. A triplex comes to 4.5 spaces, and Section 35-526(i) requires a full space for a fraction when fewer than five spaces are required, which makes 5.
Can I build townhouses on an R-4 lot in San Antonio? +
San Antonio UDC Table 311-1 permits "Dwelling - 1 Family (Attached or Townhouse)" by right in R-6, R-5, R-4, the R-3, R-2 and R-1 column, the RM districts and the MF districts. Section 35-373(b) sets a minimum lot of 1,200 square feet and 15 feet of width, with no front or side yard required. Each townhouse sits on its own platted lot.
How tall can a townhouse be in San Antonio? +
San Antonio UDC 35-373(b)(9) says a townhouse "shall have a maximum of three (3) floors in any zoning district" and a maximum of four floors in an approved IDZ zoning district or the downtown (D) district. The height limit of the base district in Table 310-1 still applies, which is 35 feet in the R-6 to R-3 and RM districts.
What is cottage housing in San Antonio? +
San Antonio UDC 35-373(d) defines a cottage as a single-family detached dwelling in a cottage housing development. The site must be at least 11,600 square feet. A cottage may not exceed 18 feet or 1½ stories, its main floor may not exceed 800 square feet, and its total floor area may not exceed 975 square feet. Each unit needs 400 square feet of common open space.
What is IDZ zoning in San Antonio? +
IDZ is the San Antonio Infill Development Zone in UDC 35-343.01, a district for vacant or underused land in older parts of the city. IDZ-1 allows up to 18 dwelling units per acre and IDZ-2 up to 50. Lots may be platted with no minimum lot area, except that a detached house needs 1,250 square feet. City Council approves each IDZ by rezoning.
Can I build apartments on commercial land in San Antonio without rezoning? +
Yes, on qualifying land. San Antonio UDC 35-312 lets property zoned office, commercial, light industrial, business park, infill development zone or mixed use be developed as multifamily or mixed-use residential "without needing to rezone," at up to 65 units per acre. The section does not apply within 3,000 feet of an airport or military base or within 1,000 feet of a heavy industrial use.
How tall can housing be on commercial land under San Antonio UDC 35-312? +
San Antonio UDC 35-312(d) allows a maximum building height "equivalent to the limitation imposed by the base zoning district or forty-five (45) feet, whichever is greater." Setbacks are those of the base district or 25 feet, whichever is less. The project needs no more than one off-street parking space per dwelling unit and has no floor to area ratio limit.
Does a San Antonio triplex or fourplex need a site work permit? +
It depends on the layout. City of San Antonio Information Bulletin 225 says a separate Site Work Permit is needed when three or more dwelling units are proposed on a single platted lot where one or more homes do not front a public or private street. Shared parking, private utilities, and a site over the Edwards Recharge Zone District also require one.
How close to a house can an apartment building be in San Antonio? +
San Antonio UDC Table 310-1 sets a 40-foot rear setback for an MF-18 to MF-50 district that adjoins a platted subdivision zoned for single-family use, and parking must stay 5 feet from any fence on that rear line. Note 11 limits any part of a multi-family district within 50 feet of a single-family home to the height of the single-family district.

Official sources (checked October 2026)

San Antonio UDC 35-310.06, RM-6, RM-5 and RM-4 districts
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=ARTIIIZO_DIV2BAZODI_S35-310.06MIRE
San Antonio UDC 35-310.07, MF districts
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=ARTIIIZO_DIV2BAZODI_S35-310.07MFMFMFMFMFMFMUMI
San Antonio UDC 35-310.01, Table 310-1 (lot and building dimensions)
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=ARTIIIZO_DIV2BAZODI_S35-310.01GE
San Antonio UDC 35-311, use regulations and Table 311-1
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=ARTIIIZO_DIV2BAZODI_S35-311USRE
San Antonio UDC 35-312, multi-family and mixed use in non-multi-family districts
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=ARTIIIZO_DIV2BAZODI_S35-312MUFAMIUSDENLMIZODI
San Antonio UDC 35-343.01, IDZ Infill Development Zone
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=ARTIIIZO_DIV5SPDI_S35-343.01IDINDEZOCOCHZOAPSUAFNO12018
San Antonio UDC 35-373, attached dwellings
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=ARTIIIZO_DIV7SUUSRE_S35-373ATDW
San Antonio UDC 35-515, lot layout regulations
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=ARTVDEST_DIV4LOLAHEDEINST_S35-515LOLARE
San Antonio UDC 35-523, tree preservation
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=ARTVDEST_DIV5NAREPR_S35-523TRPR
San Antonio UDC 35-526, parking and loading standards
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=ARTVDEST_DIV6PASTST_S35-526PALOST
San Antonio UDC Appendix A, definitions
https://library.municode.com/tx/san_antonio/codes/unified_development_code?nodeId=APXADERUIN_S35-A101DERUIN
City of San Antonio, Information Bulletin 225, Multiple Dwelling Units on One or More Lots (PDF)
https://docsonline.sanantonio.gov/FileUploads/dsd/IB225.pdf
City of San Antonio, Information Bulletin 101, New Residential Permit Information (PDF)
https://docsonline.sanantonio.gov/FileUploads/dsd/IB101.pdf
City of San Antonio, FY 2027 Development Fee Schedule (PDF)
https://docsonline.sanantonio.gov/FileUploads/dsd/CurrentFeeSchedule.pdf
VanPlex newsletter

Get new guides by email

New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.

General information, not legal advice. Texas has no statewide zoning code. Each city writes its own rules, and deed restrictions recorded on a lot can forbid what the city allows. Confirm current requirements with the city planning department, read the deed restrictions for your lot, and talk to a Texas-licensed attorney or architect before you buy land or file plans.

Planning a multiplex in San Antonio?

VanPlex builds multiplexes in British Columbia, Canada. For a lot in San Antonio, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.

Get a proforma for your address