David Babakaiff
Written by David Babakaiff · Co-Founder, VanPlex | 25+ Years BC Construction Last reviewed: October 2026

San Diego | Zoning districts

San Diego Zoning Districts: RS, RX, RT and RM Zones and How Many Homes Each Allows

A zone is the set of rules the City attaches to a piece of land: what may be built there, how many homes, and how big. San Diego's residential zones are in Chapter 13, Article 1, Division 4 of its Municipal Code, which the City publishes as PDFs, one for each division. The copy read for this page is dated September 2026. This page explains each zone family, the number of homes each allows, and how state laws such as SB 9 and ADU law add homes on top.

San Diego zoning districts in six facts

  • San Diego has four families of residential base zones: RS (Residential, Single Unit), RX (Small Lot), RT (Townhouse) and RM (Multiple Unit), all in Chapter 13, Article 1, Division 4 of the Municipal Code. Source: SDMC 131.0403 to 131.0406
  • Every RS, RX and RT zone allows a maximum of 1 dwelling unit per lot in its own tables, before ADUs and SB 9 homes are added. Source: SDMC Tables 131-04D, 131-04E, 131-04F
  • RS minimum lot sizes run from 40,000 sq ft in RS-1-1 and RS-1-8 down to 5,000 sq ft in RS-1-7 and RS-1-14. Source: SDMC 131.0403(b)
  • The 12 RM zones allow one home for each 3,000 sq ft of lot area in RM-1-1 down to one for each 200 sq ft in RM-4-11. Source: SDMC 131.0406(b)
  • In the RS-1-2 to RS-1-7 zones the floor area ratio falls with lot size, from 0.70 on lots of 3,000 sq ft or less to 0.45 on lots over 19,000 sq ft. Source: SDMC Table 131-04J
  • SB 9 adds up to two homes per lot in single-family zones through SDMC 143.1310, on top of the one home the zone tables allow. Source: SDMC 143.1310

How San Diego Names Its Zones

Each residential zone name has four parts. The first two letters give the family: RS, RX, RT or RM. The next numbers narrow it down. In the residential zone division, RS means "Residential--Single Unit," RX means "Residential--Small Lot," RT means "Residential--Townhouse" and RM means "Residential--Multiple Unit." So RS-1-7 is the seventh zone in the first RS group, and RM-2-5 is the fifth RM zone, in the second RM group.

The stated purpose of the whole division is "to provide for areas of residential development at various specified densities throughout the City." Density here means the number of homes allowed for a given amount of land. The RS, RX and RT zones allow one main home on each lot. The RM zones allow several, and the number depends on the lot area.

You find your lot's zone on the City's Zoning and Parcel Information Portal (ZAPP), which Information Bulletin 409 names as the place to look it up. Some parts of San Diego are in planned districts, older zoning areas with their own rules in Chapter 15 of the Municipal Code; this page covers the citywide base zones only.

The RS, RX and RT Zones

Section 131.0403 says the purpose of the RS zones is "to provide appropriate regulations for the development of single dwelling units that accommodate a variety of lot sizes and residential dwelling types." There are 14 of them in two groups. RS-1-1 to RS-1-7 apply in Urbanized Communities, the older, built-up parts of the city. RS-1-8 to RS-1-14 apply in Planned Urbanized Communities or Proposition A Lands, the newer and outer parts. Each group runs through the same seven minimum lot sizes, from 40,000 square feet down to 5,000.

Zones Where or what Minimum lot area Homes per lot (zone table) Floor area ratio
RS-1-1 to RS-1-7 Urbanized Communities 40,000 / 20,000 / 15,000 / 10,000 / 8,000 / 6,000 / 5,000 sq ft 1 per lot 0.45 in RS-1-1; by lot size (Table 131-04J) in RS-1-2 to RS-1-7
RS-1-8 to RS-1-14 Planned Urbanized Communities or Proposition A Lands 40,000 / 20,000 / 15,000 / 10,000 / 8,000 / 6,000 / 5,000 sq ft 1 per lot 0.45 in RS-1-8; 0.60 in RS-1-9 to RS-1-14
RX-1-1, RX-1-2 Small lots, attached or detached houses 4,000 / 3,000 sq ft 1 per lot 0.70 / 0.80
RT-1-1 to RT-1-5 Townhouses on small lots with alleys 3,500 / 3,000 / 2,500 / 2,200 / 1,600 sq ft 1 per lot 0.85 to 1.20 (1 and 2 stories); 1.20 to 1.60 (3 stories)

Sources: SDMC 131.0403 to 131.0405 and Tables 131-04D, 131-04E, 131-04F (PDF dated 9-2026). Lot sizes are listed in zone order.

The RX zones are for "both attached and detached single dwelling units on smaller lots than are required in the RS zones." The code says they are meant as "an alternative to multiple dwelling unit developments where single dwelling unit developments could be developed at similar densities." RX-1-1 needs a 4,000 square foot lot and RX-1-2 a 3,000 square foot lot, each at least 35 feet wide.

The RT zones are for "attached, single-dwelling unit residential development on small lots with alley access." The code says they are "intended to be applied on subdivided blocks with alleys that are within or close to highly urbanized areas, transit areas, and redevelopment areas." Minimum lots run from 3,500 square feet in RT-1-1 to 1,600 in RT-1-5, where a lot may be 18 feet wide. Unlike the RS zones, the RT zones also set a maximum lot coverage, from 60 percent in RT-1-1 to 75 percent in RT-1-4 and RT-1-5.

In all three families the use table, Table 131-04B, lists "Multiple Dwelling Units" as not permitted and lists "Single Dwelling Units" as permitted. Accessory Dwelling Units, Junior Accessory Dwelling Units and Movable Tiny Houses are shown with an "L," which the legend explains as "Use is permitted with limitations." Their rules are in Chapter 14, covered on the ADUs and SB 9 page.

Floor Area in the RS Zones

Floor area ratio (FAR) is the total floor area of the buildings divided by the lot area. A ratio of 0.50 on a 6,000 square foot lot allows 3,000 square feet of floor. In RS-1-1 the ratio is a flat 0.45. In RS-1-2 to RS-1-7, Section 131.0446(a) sets it by lot size in Table 131-04J: 0.70 for lots of 3,000 square feet and less, 0.60 for lots of 4,001 to 5,000, 0.59 for 5,001 to 6,000, 0.58 for 6,001 to 7,000, and down by 0.01 for each further 1,000 square feet until it reaches 0.45 for "19,001 and greater." In RS-1-9 to RS-1-14 the ratio is 0.60, and up to 400 square feet of garage is left out of the count.

Steep land lowers the number. Where "more than 50 percent of the lot area contains steep hillsides," the ratio in RS-1-2 to RS-1-7 is based on the flat part of the lot, or the zone's minimum lot area if that is greater, plus "25 percent of the remaining lot area." The coast and hillsides page explains how the City defines a steep hillside.

This matters for added homes. Section 141.0302(b)(7)(F) says "The gross floor area of an ADU shall be included in the floor area ratio for the premises," while a junior ADU's floor area is left out. An 800 square foot ADU is protected even where the ratio is used up, as the ADU page explains.

The 12 RM Zones

Section 131.0406 says the RM zones "provide for multiple dwelling unit development at varying densities." Each RM zone sets its density as one home for a stated number of square feet of lot area. RM-1-1 to RM-1-3 "permit lower density multiple dwelling units with some characteristics of single dwelling units." RM-2-4 to RM-2-6 permit medium density. RM-3-7 to RM-3-9 add "limited commercial uses," and RM-4-10 and RM-4-11 are "urbanized, high density" zones. RM-5-12 allows visitor lodging or homes at one per 1,000 square feet.

Zone Lot area per home (sq ft) Minimum lot (sq ft) Maximum floor area ratio Base height (ft)
RM-1-1 3,000 6,000 0.75 (1 to 2 homes), 1.0 (3 to 7), 1.25 (8 or more) 30
RM-1-2 2,500 6,000 0.90 (1 to 2 homes), 1.0 (3 to 7), 1.25 (8 or more) 30
RM-1-3 2,000 6,000 1.05 (1 to 7 homes), 1.25 (8 or more) 30
RM-2-4 1,750 6,000 1.20 (1 to 7 homes), 1.25 (8 or more) 40
RM-2-5 1,500 6,000 1.35 40
RM-2-6 1,250 6,000 1.50 40
RM-3-7 1,000 7,000 1.80 40
RM-3-8 800 7,000 2.25 50
RM-3-9 600 7,000 2.70 60
RM-4-10 400 7,000 3.60 none in the table
RM-4-11 200 7,000 7.20 none in the table
RM-5-12 1,000 10,000 1.80, rising with height (Table 131-04K) none in the table

Source: SDMC 131.0406 and Table 131-04G (PDF dated 9-2026). Table footnotes change some values in the Peninsula and Ocean Beach community plan areas, in La Jolla, Pacific Beach and Torrey Pines, and on historic sites.

By VanPlex arithmetic, a 6,000 square foot lot holds two homes in RM-1-1 (6,000 divided by 3,000), three in RM-1-3 and four in RM-2-5, and a 7,000 square foot RM-3-7 lot, the smallest that zone allows, holds seven. Table 131-04G footnote 1 says density is "One dwelling unit per specified square foot of lot area as determined in accordance with Section 113.0222," and footnote 2 says an exception may be allowed through the Affordable Housing Regulations. The three or more homes page covers those bonus programs.

The table footnotes hold local exceptions. In the Peninsula and Ocean Beach community plan areas, RM-2-4 has a maximum floor area ratio of 0.70 for one or two homes and 1.0 for three to seven. In the La Jolla, Pacific Beach and Torrey Pines community plan areas, RM-5-12 allows one home "for each 1,500 square feet of lot area." And for a site in a historic district or on a designated historical resource, footnote 39 says "the maximum floor area ratio shall not increase" for the higher ratios in RM-1-1, RM-1-3 and RM-2-4.

What SB 9 and ADUs Add to Each Zone

The zone tables are the starting point. State law adds homes on top, and San Diego has written those additions into Chapter 14 of its code.

  • ADUs and junior ADUs. Section 141.0302 allows them in every zone where the use table shows "L." An accessory dwelling unit (ADU) is a second, smaller home on a lot that keeps its main house. A junior ADU (JADU) is a unit of up to 500 square feet inside the house or an attached garage. ADUs "are not subject to the density limitations of the base zone."
  • SB 9 homes. Section 143.1310 allows "Up to two dwelling units" on a lot in a zone "that permits single dwelling unit development, but not multiple dwelling unit development." The use table entry stays a dash; Section 131.0420(a)(4) says the uses in a residential zone "may be further limited or expanded" by the SB 9 division.
  • ADU Home Density Bonus. A City program that allows bonus ADUs beyond state law, up to 4, 5 or 6 ADUs in total on single-family lots by lot size. It is barred in RS-1-1 to RS-1-4 and RS-1-8 to RS-1-11 unless the lot is in a High or Highest Resource area and is shown as residential in a land use plan.

The code is not consistent about which zones SB 9 covers. Section 143.1303(a) says the division applies in "RS, RX, RT and Planned District Zones." Section 143.1310 and Information Bulletin 409 list "RS, RE, RX, and RT zones." The residential base zone division read for this page defines no RE zone. Section 143.1303 is the section that says where the division applies; if your lot is zoned RE, ask Development Services which reading it uses.

Rules That Apply in Every Residential Zone

Section 131.0430 says no structure may be built unless it complies with the zone's rules "and with any applicable development regulations in Chapter 13, Article 2 (Overlay Zones) and Chapter 14." An overlay zone is a second map layer, such as the Coastal Overlay Zone, that adds rules on top of the base zone. The same section says the zone rules "apply to all development in the residential base zones whether or not a permit or other approval is required."

Every zone table ends with a row for the "Dwelling Unit Protection Regulations," which require a new project to replace the homes it removes. Some uses need a permit even when the zone allows them: Section 131.0430(b) points to Table 143-03A for development that needs a Neighborhood Development Permit or Site Development Permit. The permits and fees page explains what those permits are.

Watch the coastal notes. Many amendments to these sections carry the City's editors note that they "will not apply within the Coastal Overlay Zone until the California Coastal Commission certifies it as a Local Coastal Program Amendment." Ordinance O-22109, which the code records as amending the residential use table on June 15, 2026 with effect from July 15, 2026, carries this note. Inside the coastal zone, the version before that ordinance applies until certification.

Best For

  • ✓ An RM-2-5 or denser lot of 6,000 sq ft or more, where the zone itself allows four or more homes.
  • ✓ An RS-1-7 lot of 5,000 to 6,000 sq ft, where SB 9 and ADUs add homes the zone table does not count.
  • ✓ An RT lot on an alley block, where townhouse rules allow up to 75 percent lot coverage.

Usually Fails When

  • ✕ The plan counts RM density but forgets that ADU floor area still counts toward the floor area ratio.
  • ✕ The lot is in RS-1-1 to RS-1-4 or RS-1-8 to RS-1-11 and the plan relies on bonus ADUs outside a High or Highest Resource area.
  • ✕ The lot is in the Coastal Overlay Zone and the plan relies on a 2026 amendment the Coastal Commission has not certified.

What To Verify Before Spending Money

  • → Your zone and any planned district on ZAPP.
  • → Whether more than half of the lot is steep hillside, which lowers the RS floor area ratio.
  • → Whether a community plan footnote in Table 131-04G changes the floor area or density for your area.

Where to Go Next

Related on VanPlex: the San Diego overview, SB 9 in California and California ADU law.

Frequently Asked Questions

What does the RS zone mean in San Diego? +
RS stands for Residential, Single Unit. San Diego Municipal Code 131.0403 says the RS zones provide for single dwelling units on a variety of lot sizes. There are 14 RS zones, split into two groups of seven by Development Character Area, and every one allows 1 dwelling unit per lot in Table 131-04D, before ADUs or SB 9 homes are counted.
How many homes can I build on an RM-2-5 lot in San Diego? +
An RM-2-5 lot in San Diego allows one home for each 1,500 square feet of lot area under Municipal Code 131.0406. On the minimum RM-2-5 lot of 6,000 square feet that is four homes by VanPlex arithmetic (6,000 divided by 1,500). ADUs are added on top, because Section 141.0302 says ADUs are not subject to the density limits of the base zone.
What is the difference between RX and RT zones in San Diego? +
San Diego RX zones are small-lot zones of 4,000 or 3,000 square feet for attached or detached houses, while RT zones are townhouse zones of 3,500 down to 1,600 square feet meant for blocks with alleys. Both allow 1 dwelling unit per lot in their tables. RT lots can be 18 feet wide in RT-1-5; RX lots are at least 35 feet wide.
Can I build a duplex in an RS zone in San Diego? +
Yes, through SB 9. San Diego Municipal Code 143.1310 allows up to two dwelling units on a premises in a zone that permits single dwelling units but not multiple dwelling units, attached or detached. The zone use table itself lists Multiple Dwelling Units as not permitted in RS, RX and RT zones, so SB 9 is the path.
What floor area can a house have on a 6,000 square foot RS-1-7 lot in San Diego? +
A San Diego RS-1-7 lot of 6,000 square feet has a maximum floor area ratio of 0.59 under Table 131-04J, which is 3,540 square feet of gross floor area by VanPlex arithmetic. ADU floor area counts toward that ratio, but a junior ADU does not. The ratio falls on larger lots, to 0.45 above 19,000 square feet.
Which San Diego RS zones are in Planned Urbanized Communities? +
San Diego Municipal Code 131.0403(b) places RS-1-8 to RS-1-14 in Planned Urbanized Communities or Proposition A Lands, and RS-1-1 to RS-1-7 in Urbanized Communities. The two groups share lot sizes but differ in other rules: RS-1-8 to RS-1-14 have a flat 35-foot height limit and a 10-foot rear setback in Table 131-04D.
Do ADUs count toward density in San Diego RM zones? +
No. San Diego Municipal Code 141.0302(b)(6) says ADUs are not subject to the density limitations of the base zone, and 141.0302(c)(3) says the same for junior ADUs. ADU gross floor area still counts toward the floor area ratio of the lot under 141.0302(b)(7)(F), so on an RM lot the floor area limit is usually what limits extra ADUs.
Why does a San Diego zoning rule apply differently near the coast? +
Many San Diego zoning amendments carry an editors note saying they will not apply within the Coastal Overlay Zone until the California Coastal Commission certifies them. The residential use table, for example, was amended by Ordinance O-22109, effective July 15, 2026, and that change waits for certification inside the coastal zone. Check which version applies to your lot.
Can a San Diego RM-1-1 lot be split into small lots for houses? +
Yes, through a small lot subdivision. San Diego Municipal Code 143.0365 allows small lot subdivisions in the RM-1-1 through RM-3-8 zones, with one dwelling unit per subdivided lot and density set by the base zone. It needs a Site Development Permit, decided in Process Three, and each home may have at most three bedrooms.
Is there a maximum height in San Diego RM-4-10 and RM-4-11 zones? +
San Diego Table 131-04G shows no base height number for RM-4-10, RM-4-11 and RM-5-12, with a footnote instead. Footnote 37 says that within the Coastal Height Limit Overlay Zone in the Peninsula Community Plan area, the base zone height is 30 feet. Overlay zones and community plans can also set height limits for these lots.

Official sources (checked October 2026)

VanPlex newsletter

Get new guides by email

New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.

General information, not legal advice. California housing law changes every year, and each city adds its own rules on top of state law. Confirm current requirements with the city or county planning department, and with a California-licensed attorney or architect, before you buy land or file plans.

Planning a multiplex in San Diego?

VanPlex builds multiplexes in British Columbia, Canada. For a lot in San Diego, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.

Get a proforma for your address