Oakland | Parking, Setbacks, Height
Oakland Parking, Setbacks and Height: Parking by Building Type, Setbacks by Zone, Height and Lot Coverage
Once a zone allows a number of homes, four building rules decide whether they fit: parking, setbacks, height and lot coverage. A setback is the open distance a building must keep from a lot line. Lot coverage is the share of the lot covered by buildings, and floor area ratio (FAR) is the total floor area divided by the lot area. Oakland sets these rules zone by zone in the Planning Code, with general rules in Chapter 17.108 and parking in Chapter 17.116. The figures below are from Supplement 59.
Oakland building limits in six facts
- A Two- to Four-Family or Multifamily Dwelling needs half a parking space per unit in most zones, and none within half a mile of a major transit stop. Source: Planning Code 17.116.060
- On RD and RM lots of 3,000 sq ft or more, the minimum setbacks are 15 feet in front, 4 feet on each side and 10 feet at the rear; lots under 3,000 sq ft need 3-foot sides. Source: Tables 17.15.03, 17.15.04, 17.17.03
- On flatter lots the RD zone allows a 30-foot wall height and a 35-foot pitched roof; RM-3 and RM-4 allow 35 feet for both. Source: Tables 17.15.03 and 17.17.03
- The RH hill zones cap wall height at 25 feet and pitched roofs at 30 feet on lots with a footprint slope under 20 percent, with rear setbacks of 20 to 35 feet. Source: Planning Code, Table 17.13.03
- Lot coverage and floor area limits apply in RD and RM only to lots with one or two units; a house lot under 6,000 sq ft may cover 55 percent. Source: Tables 17.15.05 and 17.17.05
- RU buildings next to an RH, RD or RM lot are limited to 30 feet at the setback line, rising one or two feet for each foot of distance. Source: Planning Code, Table 17.19.03
Parking for Homes
Section 17.116.060 sets the minimum number of off-street parking spaces by building type and zone. The table is the residential part of it.
| Building type | Zone | Minimum parking |
|---|---|---|
| One-Family Dwelling | RH zones (not S-9 or S-11) | 2 per unit; none within ½ mile of a major transit stop |
| One-Family Dwelling | RH zones with S-9 or S-11 | 1 per bedroom, at least 2 and at most 4 per unit; none within ½ mile of a major transit stop |
| One-Family Dwelling | Any other zone | 1 per unit; none within ½ mile of a major transit stop |
| Two- to Four-Family or Multifamily Dwelling | All zones except D-DT, S-15, D-CO-1, D-LM | ½ per unit; none within ½ mile of a major transit stop |
| Two- to Four-Family or Multifamily Dwelling | D-DT, S-15, D-CO-1, D-LM | None |
| Accessory Dwelling Unit | Most zones, including S-9 and S-11 | 1 per ADU, except where Section 17.103.080 exempts it |
Source: Oakland Planning Code Section 17.116.060.A.1, as amended by Ordinance No. 13812 (July 30, 2024). A major transit stop is as defined in Public Resources Code Section 21155.
The code repeats one phrase on almost every row: "except that no parking shall be required if located within ½-mile of a major transit stop, as defined in Section 21155 of the Public Resources Code." Ask the Planning Bureau to confirm whether your lot is inside that half mile, because the answer can take the parking minimum to zero.
Elsewhere the count is simple. Section 17.116.050 says "If after calculating the number of required off-street parking spaces a quotient is obtained containing a fraction of one-half or more, an additional space shall be required; if such fraction is less than one-half it may be disregarded." A worked example by VanPlex: a triplex needs 1.5 spaces, which rounds to 2; a fourplex needs 2; a duplex needs 1. Section 17.116.060.A.2 sets no parking maximum outside the D-DT, D-LM, S-15 and D-CO-1 zones.
Two more rules help when adding homes to old buildings. Section 17.116.020 says the parking rules "shall only apply to activities occupying any portion of new facilities and new additions," and "no additional parking and loading spaces are required for newly established living units located entirely within an existing facility and outside of the S-9 Fire Safety Protection Combining Zone." Existing spaces that meet or fall below the requirement must be kept. State law adds a further cap. Government Code 65863.2 says a public agency "shall not impose or enforce any minimum automobile parking requirement on a residential, commercial, or other development project if the project is located within one-half mile of public transit," with an exception that needs written findings within 30 days.
Garage and Driveway Design
Section 17.116.300 shapes parking on lots with one or two homes. Where "At least sixty percent (60%) of the buildings in the immediate context have parking located to the rear or side," garages and parking must also go "To the rear or side of any primary Residential Facility." The immediate context is "the five (5) closest lots on each side of the project site plus the ten (10) closest lots on the opposite side of the street." Lots under 35 feet wide are exempt if the garage takes less than half the front.
Garages and carports "shall have a maximum width of twenty-two (22) feet if the front of the garage or carport is located within thirty (30) feet of a street line," and on flatter lots an attached garage near the street may not exceed "fifty percent (50%) of the total width of the primary Residential Facility." The zone tables add that in street-facing yards on lots with only homes, paved surface is limited "to fifty percent (50%) on interior lots and thirty percent (30%) on corner lots." Exceptions to Section 17.116.300 are possible through design review.
Setbacks by Zone
| Zone | Front | Sides | Rear |
|---|---|---|---|
| RD, RM-1 to RM-4 | 15 ft (5 ft if gradient over 20%) | 4 ft interior and street side | 10 ft |
| RD, RM, lots under 3,000 sq ft | 15 ft (5 ft if gradient over 20%) | 3 ft interior and street side | 10 ft |
| RU-1 | 15 ft | 4 ft | 10 ft |
| RU-2 | 10 ft | 4 ft | 10 ft |
| RU-3 | 10 ft | 3 ft | 10 ft |
| RU-4 / RU-5 | 5 ft / 0 ft | 0 ft | 10 ft |
| RH-1 / RH-2 | 25 ft | 6 ft, or 15% of lot width on steep lots | 35 ft / 30 ft |
| RH-3 | 20 ft | 6 ft, or 10% of lot width on steep lots | 25 ft |
| RH-4 | 20 ft | 5 ft, or 10% of lot width on steep lots | 20 ft |
Source: Oakland Planning Code Tables 17.15.03 and 17.15.04, 17.17.03 and 17.17.04, 17.19.03 and 17.13.03. RU front setbacks are for Residential Facilities on lots of 3,000 sq ft or more with a gradient of 20% or less.
The street-to-setback gradient is the slope of the ground between the street and the front setback line. Where it exceeds 20 percent, the front setback in RD, RM and RU drops to 5 feet, "provided, however," that a garage or carport with a car entry stays at least 18 feet back from the street or sidewalk pavement. The RH zones have the same 5-foot rule.
Several notes change these numbers on real lots:
- Front setback averaging. If both neighbors' houses sit closer to the street than the minimum, the front setback is reduced "up to a line parallel to the front lot line and extended from the most forward projection" of the neighbor with the deeper setback.
- Deep lots. In RD, the rear setback grows "an additional one-half (½) foot of rear setback depth for each additional one (1) foot of lot depth over one hundred (100) feet, up to a maximum rear setback depth of twenty (20) feet." In the RH zones the same rule runs to 40 feet.
- Alleys. "one-half (½) of the right-of-way width of the alley may be counted toward the required minimum rear setback," though at least 10 feet must remain on the lot.
- Side-by-side projects. "For developments involving the creation of new units on two or more adjoining parcels under the same ownership, there is no minimum interior side setback required between those new units."
- Living room windows. On lots with two or more units, Section 17.108.080 requires a side yard opposite a legally required living room window of "four (4) feet, plus one (1) foot for each story at or above the level of the aforesaid window," capped at 10 percent of lot width but never under 4 feet.
- RU next to houses. Where an RU-3, RU-4 or RU-5 lot shares a side line with an RH or RD lot, "a side setback of six (6) feet is required"; next to RM or RU-1, four feet.
Height Limits
Oakland measures two heights on flatter lots: wall height, to the top of the wall, and pitched roof height, to the top of a sloped roof. The table applies to lots with a footprint slope of 20 percent or less. Section 17.09.040 defines footprint slope as "the deviation of the ground surface from the horizontal, expressed as a percentage, measured at the steepest point between opposite sides of the building footprint."
| Zone | Wall height, main building | Pitched roof height |
|---|---|---|
| RD | 30 ft | 35 ft |
| RM-1, RM-2 | 30 ft | 35 ft (RM-2 needs a 4:12 roof pitch) |
| RM-3, RM-4 | 35 ft | 35 ft |
| RH-1 to RH-4 | 25 ft | 30 ft |
| RU-1 / RU-2 / RU-3 | 45 ft / 55 ft / 65 ft (one building height) | Same |
| Accessory structures in RH, RD, RM, RU-1 to RU-3 | 15 ft | 15 ft |
Source: Oakland Planning Code Tables 17.13.03, 17.15.03, 17.17.03 and 17.19.03. RU-4 and RU-5 heights come from the height area on the zoning map (Table 17.19.04).
Steep lots use separate tables: 17.13.05 for RH, 17.15.06 for RD and 17.17.06 for RM. In RD and RM, a downslope lot steeper than 20 percent and under 40 percent allows a 30-foot wall and 35-foot roof; 40 to 60 percent allows 32 and 36 feet; over 60 percent allows 34 and 38 feet. On these downslope lots the building may rise no more than 18 feet above the edge of the street pavement. On upslope lots the limit is 24 feet within 20 feet of the front property line and 24 feet above the ground at the rear setback line. In RH, downslope walls may reach 32, 34 or 36 feet, or more "with a CUP," a Conditional Use Permit.
The hills have one more height rule. In all RH zones, "if at least sixty percent (60%) of the buildings in the immediate context are no more than one (1) story in height, the maximum wall height shall be fifteen (15) feet within the front twelve (12) feet of buildable area." Next to RH, RD and RM lots, RU buildings "shall have a thirty (30) foot maximum height at the setback line," rising one foot per foot of distance, or two feet per foot when the neighbor is over 30 feet tall. Section 17.108.030 allows chimneys, vents and similar equipment to project up to 10 feet above the limit, and Section 17.108.020 adds one foot per story for buildings made with volumetric modular construction, factory-built room modules.
Lot Coverage and Floor Area for One or Two Units
In RD and RM, these limits apply only to lots with one or two units, not counting ADUs. Table 17.15.05 (and the matching Table 17.17.05) reads:
| Lot size | Maximum FAR (footprint slope over 20%) | Maximum lot coverage |
|---|---|---|
| Under 6,000 sq ft | 0.55 | 55% |
| 6,000 to under 12,000 sq ft | 0.50 | 45% |
| 12,000 to under 25,000 sq ft | 0.45 | 30% |
| 25,000 to under 43,560 sq ft | 0.30 | 20% |
| 43,560 sq ft and over | 0.20 | 15% |
Source: Oakland Planning Code Table 17.15.05 and Table 17.17.05, Maximum Floor Area Ratio and Lot Coverage for One and Two Dwelling Units Only.
The FAR row "only applies to lots that have a footprint slope of greater than twenty percent (20%)," and "Lots less than four thousand (4,000) square feet may have a minimum of two thousand (2,000) square feet of floor area." Lots under 4,000 square feet may also cover up to 2,000 square feet whatever the percentage. A worked example by VanPlex: a flat 5,000 square foot RD lot with one house may cover 2,750 square feet (55 percent) and has no FAR limit. The RH zones use Table 17.13.04, which caps coverage at 40 percent on lots up to 12,000 square feet and sets FAR from 0.55 to 0.20 on every lot. For three or more units in RD and RM, neither limit applies, as the three or more homes page explains.
Best For
- ✓ Lots within half a mile of a major transit stop, where most residential parking minimums do not apply.
- ✓ Flat RM-3 and RM-4 lots, which allow a 35-foot wall height.
- ✓ Triplexes and fourplexes in RD and RM, which have no lot coverage or FAR cap.
Usually Fails When
- ✕ An RH lot where most neighbors are one story, which caps the front wall at 15 feet.
- ✕ A steep downslope lot where the design rises more than 18 feet above the street pavement.
- ✕ A side yard faces a neighbor's required living room window and the plan leaves only 3 feet.
What To Verify Before Spending Money
- → The footprint slope and street-to-setback gradient, measured by a surveyor.
- → The distance to the nearest major transit stop under Public Resources Code 21155.
- → Any S-11 or S-12 combining zone, which adds parking standards.
Where to Go Next
Related on VanPlex: the Oakland and Berkeley overview and the duplex to fourplex guide.
Frequently Asked Questions
How much parking does a fourplex need in Oakland?
Does a new house in the Oakland hills need two parking spaces?
What are the setbacks for a fourplex on an Oakland RD lot?
How tall can I build in Oakland's RM-4 zone?
How much open space does a fourplex need in Oakland's RM zones?
How much of an Oakland lot can a house cover?
How wide can a garage be in Oakland?
What is a footprint slope in the Oakland Planning Code?
Do I need extra side yard next to a living room window in Oakland?
Can state law remove parking near transit in Oakland?
Official sources (checked October 2026)
Get new guides by email
New VanPlex guides and articles on multiplex rules, building costs and permits, sent to your inbox.
Planning a multiplex in Oakland?
VanPlex builds multiplexes in British Columbia, Canada. For a lot in Oakland, our team makes a custom proforma by hand and emails it to you in 24 to 48 hours.
Get a proforma for your address